questions, i'm getting close
#1
questions, i'm getting close
1. what do i need for vaccuum tee's? do i just go to the autozone and get some? is there a certain size?
2. on that topic, how do i run my boost guage into an existing vaccuum line? it only comes with the hose, and a bunch of ---- i would need if i were going to tap my manifold.
3. if I am going to run water lines, where do i run them from/to and what do i need to do so?
4. when i lower my boost via actuator arm, i want it to be longer right? or shorter?
5. would it be better for me to run the wastegate at 5psi and use an mbc for 3 extra psi? or just run 8psi at the wg?
6. do i really need to have an adapter coupler from 2.5" to 2.25" (ic pipe to ic) or from 2.25" to 2" ic pipe to turbo)? or could i just use 2.25" straight couplers?
7. what is the diameter on a stock y8 tb?
if i come up with anything else, i'll put it in here, i'm just getting down to the wire (2 weeks till install day) thanx for the help.
2. on that topic, how do i run my boost guage into an existing vaccuum line? it only comes with the hose, and a bunch of ---- i would need if i were going to tap my manifold.
3. if I am going to run water lines, where do i run them from/to and what do i need to do so?
4. when i lower my boost via actuator arm, i want it to be longer right? or shorter?
5. would it be better for me to run the wastegate at 5psi and use an mbc for 3 extra psi? or just run 8psi at the wg?
6. do i really need to have an adapter coupler from 2.5" to 2.25" (ic pipe to ic) or from 2.25" to 2" ic pipe to turbo)? or could i just use 2.25" straight couplers?
7. what is the diameter on a stock y8 tb?
if i come up with anything else, i'll put it in here, i'm just getting down to the wire (2 weeks till install day) thanx for the help.
#2
Re:questions, i'm getting close
1.They have diff. sizes, so take the vacuum hose you are going to use.
2.Use a T and tap in a vacuum source after the TB then run it all the way towards the cabin, fairly easy. Also use ties (Nylon locks) to secure all the hoses when attached to the T's.
3.Coolant runs right under the TB and either hole (on the turbo) could be the in and out (its not like the oil).
5.Set it at 8 psi, 'cause you'll probably going to lose boost due to piping and intercooler, so check your gauge then adjust boost through the MBC.
7.TB diameter is 2.5"
2.Use a T and tap in a vacuum source after the TB then run it all the way towards the cabin, fairly easy. Also use ties (Nylon locks) to secure all the hoses when attached to the T's.
3.Coolant runs right under the TB and either hole (on the turbo) could be the in and out (its not like the oil).
5.Set it at 8 psi, 'cause you'll probably going to lose boost due to piping and intercooler, so check your gauge then adjust boost through the MBC.
7.TB diameter is 2.5"
#4
Re:questions, i'm getting close
Originally Posted by bambooseven
8. will my stock ehuast mani studs be ok for the HF mani?
But not all blocks have the corosponding holes on the block to match the manifold, I think its only obd0 engines that have it.
Thread
Thread Starter
Forum
Replies
Last Post
bonylad
Forced Induction
17
11-21-2005 12:12 PM
d16u7nh
Hybrid/Tech
7
11-11-2005 03:09 PM
falkhen
General Discussion
18
04-18-2005 09:45 PM