Canadian D *updated 02/6/09
Thread Starter
0.5 BAR
Joined: Dec 2006
Posts: 113
Re: Canadian D *updated 01/09/09
Originally Posted by Urban Indian
i just wanted to watch him carry this bitch. He weighs 105lbs soaking wett with bricks in his pockets. It must have been some sight lol.
I'm interested in relevant RING GAP suggestions please. (for the lazy ***** = d16z6 75mm ball honed perfection)
I've only looked in the KB catalog under suggested gap/in of bore for street/strip forced induction so far.
Have ring file ready for this week's HRN.
Thread Starter
0.5 BAR
Joined: Dec 2006
Posts: 113
Re: Canadian D *updated 01/23/09
Pistons got rings and dropped into the bores and all the rotating assembly is now tightened up as of last night
Checking Ring gap... came out to .018" top and .022" second out of the box seemed more than big enough. (.0065/in and .0075/in resp.)
The infinite spellabilites of the asian market....haha coating gives you increased strenghth's
I think it also suggests for max perf. that the pistons be kept to low RPMs 
Shop's AC and heating systems.
To access to your race car in BC you need one of these (note this is a 25yo Eaton's VIKING model top not ---- damn near throws the snow over the house)
The parts safely stowed away.
Checking Ring gap... came out to .018" top and .022" second out of the box seemed more than big enough. (.0065/in and .0075/in resp.)
The infinite spellabilites of the asian market....haha coating gives you increased strenghth's
I think it also suggests for max perf. that the pistons be kept to low RPMs Shop's AC and heating systems.
To access to your race car in BC you need one of these (note this is a 25yo Eaton's VIKING model top not ---- damn near throws the snow over the house)
The parts safely stowed away.
0.0 BAR
Joined: Aug 2007
Posts: 0
From: Okotoks, AB
Re: Canadian D *updated 01/23/09
Originally Posted by brine04
Pretty sure you are supposed to put the arrows towards the flywheel side as the suzuki motors rotate the opposite of the honda motors, double check though nig.
Thread Starter
0.5 BAR
Joined: Dec 2006
Posts: 113
Re: Canadian D *updated 01/23/09
hmmm dirty African sack licker!!! 
why isn't the whole world obvious.
quick search shows mixed results so FJT.... you have a PM and others are welcome to throw down your opinion only if you matter tho.
See here the STD 000000 text is on the oposite side to mine inidicating the arrows if i could see them would prob point to the fly
a d-series.org build shows the arrows clearly same as mine.
EDIT: ok shitt did some more reading... and it seems like a good idea for the the valve reliefs and pin offset to be as close to stock as possible (haha) especially with the piston at almost 0 deck.
Anyone have any dimensional info RE the pin offset in the two pistons?
I'll likely end up reistalling them if tis the right thing to do.
why isn't the whole world obvious.
quick search shows mixed results so FJT.... you have a PM and others are welcome to throw down your opinion only if you matter tho.
See here the STD 000000 text is on the oposite side to mine inidicating the arrows if i could see them would prob point to the fly
a d-series.org build shows the arrows clearly same as mine.
EDIT: ok shitt did some more reading... and it seems like a good idea for the the valve reliefs and pin offset to be as close to stock as possible (haha) especially with the piston at almost 0 deck.
Anyone have any dimensional info RE the pin offset in the two pistons?
I'll likely end up reistalling them if tis the right thing to do.
