1991civicsi build thread
#51
Re: Completed Turbo EF *Video Updated*
Holy F!!!! Dude, you did all that work, learned your way through building your car...and you made that super suck *** vid! I can't even hear the damn car...I can't even see it go, I can't even get a driver view while you go down the highway. What the hell. There are simple ingredients to a good vid man...and you missed them all :1
#53
Re: Completed Turbo EF *Video Updated*
Originally Posted by rc000e
Holy F!!!! Dude, you did all that work, learned your way through building your car...and you made that super suck *** vid! I can't even hear the damn car...I can't even see it go, I can't even get a driver view while you go down the highway. What the hell. There are simple ingredients to a good vid man...and you missed them all :1
Originally Posted by iLLstate
no rippers, no burnout at least post **** after a video like that
Originally Posted by evo_lucian
yeah. the vid sucked man.
#54
Re: Completed Turbo ED
Originally Posted by 1991civicsi
To really see the DP I would have to remove it, but I can take pics and explain. Using 2.5" stainless steel 180 degree and 90 degree bends, the piping is directed toward the notch near the center of the crossmember. Then, towards the rear of the car. The cold side uses a Turbonetics 90 degree cast aluminum elbow to direct the flow towards the left side of the IC.
Thanks for the comments.
Thanks for the comments.
#56
Re: Completed Turbo EF *UPDATE*
So I did some more work and I hope you like the pics, This is how it looks from outside......
before painting the hood duct that helps keep under hood temps down (couldnt spend over $100 on an aftermarket hood)
and after spray painting it. :P
Trans Am fender vent off ebay
Some dirty engine bay pics (during sanding the hood)
This turbo is from Blaast, its a T3/T4 60trim and after installing the ETD traction bars running the D/P and charge pipe were less complicated and not criss cross like before. The dump tube was also routed back into the D/P
Here is the ebay 1/2 rad mounted w/an EG overflow tank
On the left, mounted on the headlight support, you can see the dual stage boost controller. 1st stage is off the w/g (7psi), and the 2nd stage, which is activated by a neat little lighted switch on the dash, bumps boost to 12psi.
The trans looks new b/c I just cleaned it up when I had it off the car to install a 6 puck Comp Clutch from Xenocron.
Here is the spare D16 block I bought off of AJxr. RayRay gave me the V/C and the head, which he ported himself. The engine stand belongs to HMT's D16Y8-Z6.
The Y8 IM was bought off of Loserkidwac, and I got the 70mm T/B off ebay for $50.
Brand new RC550's off Honda Tech's AnthraxVX
ebay 75.5mm Vitaras
ebay rods not SCAT, but CAT. LOL
Side by side comparison - H-beam vs Stock
The block needs to be notched to accomodate the larger H beams so I did my homework by checking ENDYN's
website.
Went to town w/ a carbide cutter.
Got my BOV off ebay
before painting the hood duct that helps keep under hood temps down (couldnt spend over $100 on an aftermarket hood)
and after spray painting it. :P
Trans Am fender vent off ebay
Some dirty engine bay pics (during sanding the hood)
This turbo is from Blaast, its a T3/T4 60trim and after installing the ETD traction bars running the D/P and charge pipe were less complicated and not criss cross like before. The dump tube was also routed back into the D/P
Here is the ebay 1/2 rad mounted w/an EG overflow tank
On the left, mounted on the headlight support, you can see the dual stage boost controller. 1st stage is off the w/g (7psi), and the 2nd stage, which is activated by a neat little lighted switch on the dash, bumps boost to 12psi.
The trans looks new b/c I just cleaned it up when I had it off the car to install a 6 puck Comp Clutch from Xenocron.
Here is the spare D16 block I bought off of AJxr. RayRay gave me the V/C and the head, which he ported himself. The engine stand belongs to HMT's D16Y8-Z6.
The Y8 IM was bought off of Loserkidwac, and I got the 70mm T/B off ebay for $50.
Brand new RC550's off Honda Tech's AnthraxVX
ebay 75.5mm Vitaras
ebay rods not SCAT, but CAT. LOL
Side by side comparison - H-beam vs Stock
The block needs to be notched to accomodate the larger H beams so I did my homework by checking ENDYN's
website.
Went to town w/ a carbide cutter.
Got my BOV off ebay
#60
Re: Completed Turbo EF *UPDATE*
Originally Posted by ososlohatch
solid ---- yo
Originally Posted by crxvtec91
Hey what part of Nj you from, really clean setup.
Originally Posted by PhilStubbs
cant wait to see how those ebay vitaras work. i want to get some myself, but i am afraid that they arent the real thing