I need a T04S 60-1 compressor map
#1
I need a T04S 60-1 compressor map
I would like a compressor map for the turbo Im running, but i cannot find it anywhere. I chose the turbo soley on others experience, but I am getting the hang of plotting on maps so I would like to to where I stand.
Its a garrett TO4S 60-1 compressor. 46 trim.
Thanks in advance.
Its a garrett TO4S 60-1 compressor. 46 trim.
Thanks in advance.
#3
Re: I need a T04S 60-1 compressor map
This is a map for that turbo but it doesn't say what the A/R is.(or i don't see it)
http://www.not2fast.com/turbo/maps/t04b-60-1.gif
Here is the page i found it on
http://www.not2fast.com/turbo/maps/
Hope this helps,i am a noob but i think it will be too small also.
Mark
http://www.not2fast.com/turbo/maps/t04b-60-1.gif
Here is the page i found it on
http://www.not2fast.com/turbo/maps/
Hope this helps,i am a noob but i think it will be too small also.
Mark
#4
Re: I need a T04S 60-1 compressor map
Originally Posted by win0857
This is a map for that turbo but it doesn't say what the A/R is.(or i don't see it)
http://www.not2fast.com/turbo/maps/t04b-60-1.gif
Here is the page i found it on
http://www.not2fast.com/turbo/maps/
Hope this helps,i am a noob but i think it will be too small also.
Mark
http://www.not2fast.com/turbo/maps/t04b-60-1.gif
Here is the page i found it on
http://www.not2fast.com/turbo/maps/
Hope this helps,i am a noob but i think it will be too small also.
Mark
Its not too small. It plots where I need it actually. Only need 500hp, and 8psi should get me there.
Moostangs are going 11's with the same turbo I have.
#5
Re: I need a T04S 60-1 compressor map
Here is what I came up with. Based on these factors and after my calculations
Target horsepower-500hp
max rpm-6000
VE= 85%
Displacement=318ci
Intake Manifold temp=160 degree
55 pounds of airflow needed per minute.
Manifold absoloute pressure required= 26 psi .-14.7 atmospheric pressure= (~11psi needed)
I also plotted that at 6000rpm. Where more realistically Ill be 5200rpm MAX
See attached pic!
Target horsepower-500hp
max rpm-6000
VE= 85%
Displacement=318ci
Intake Manifold temp=160 degree
55 pounds of airflow needed per minute.
Manifold absoloute pressure required= 26 psi .-14.7 atmospheric pressure= (~11psi needed)
I also plotted that at 6000rpm. Where more realistically Ill be 5200rpm MAX
See attached pic!
#7
Re: I need a T04S 60-1 compressor map
I was looking at your map (I have a similar turbo for my is300) and noticed your plot is on the far edge of the efficiency island. I guess you won't be there all of the time with that turbo as you advised it would be at the top of the rev range. I would'nt want to run it on what appears to be the least efficient area of the map. Just my 2 cents, hope that helps.
#8
Re: I need a T04S 60-1 compressor map
Originally Posted by Dive_Miguel
I was looking at your map (I have a similar turbo for my is300) and noticed your plot is on the far edge of the efficiency island. I guess you won't be there all of the time with that turbo as you advised it would be at the top of the rev range. I would'nt want to run it on what appears to be the least efficient area of the map. Just my 2 cents, hope that helps.
Im not sure if that is the correct map for my turbo charger either. Like I said I chose it on others experience with the exact same turbo on the same C.I. engines, and they made nice straight power bands with them. (just nothing over 500hp.)
Thread
Thread Starter
Forum
Replies
Last Post