willem (enhanced/dual power) burner how to! *56k/dsl=fucked!*
#41
Re: willem (enhanced/dual power) burner how to! *56k/dsl=fucked!*
Originally Posted by Racintweek
well i got it burn them but no ID, could the burner still be bad?
#43
Re: willem (enhanced/dual power) burner how to! *56k/dsl=fucked!*
what's the exact number on the top of the chip? and no, unless they're incredibly slow, you won't notice much difference in programming/erasing them. i've used 250ns chips that burn fine and run fine in the ecu, and those are pretty ------- slow in comparison to the regular 70-90ns chips.
#48
Re: willem (enhanced/dual power) burner how to! *56k/dsl=fucked!*
Originally Posted by micksf22accord
why does it say dsl is fucked im t3 dsl.......faster than most cable.............and ship out my decals bitch cause i just payed throw pay pal
Nice write-up teg. Went to a maotes for ease in the car with one cable, but you make it easier for people to save a little $$ and still get what they need.
#49
Re: willem (enhanced/dual power) burner how to! *56k/dsl=fucked!*
I just bought a Willem dual power burner from www.mcumall.com. I use a AT29c256, so I followed this write up, but it's not working, it won't recognize the AT29c256.
I tried to switch Willem to PCB3, did'nt work. Tried several DIP configuration. When I click "Electonic ID", sometimes it show me "-----" and sometime it show "Sanyo", but never an AT29c256.
I think I've setup burner properly, jump pin #3 and #31, when I test hardware, it show "hardware present". When I try to programm chip, I got an error: "Write sector 0"
The chip was already burned on another burner (don't know wich one) and it work on my car. Just want to put a new .bin on it, but I can't program chip.
Do you have an idea what i'm doing wrong? Or maybe burner is not working properly? Could you tell me if there is something to do to test burner?
For the moment, I got only 1 chip, so I can't test with another one...
Thanks
I tried to switch Willem to PCB3, did'nt work. Tried several DIP configuration. When I click "Electonic ID", sometimes it show me "-----" and sometime it show "Sanyo", but never an AT29c256.
I think I've setup burner properly, jump pin #3 and #31, when I test hardware, it show "hardware present". When I try to programm chip, I got an error: "Write sector 0"
The chip was already burned on another burner (don't know wich one) and it work on my car. Just want to put a new .bin on it, but I can't program chip.
Do you have an idea what i'm doing wrong? Or maybe burner is not working properly? Could you tell me if there is something to do to test burner?
For the moment, I got only 1 chip, so I can't test with another one...
Thanks
#50
Re: willem (enhanced/dual power) burner how to! *56k/dsl=fucked!*
Originally Posted by WhiteSI
I just bought a Willem dual power burner from www.mcumall.com. I use a AT29c256, so I followed this write up, but it's not working, it won't recognize the AT29c256.
I tried to switch Willem to PCB3, did'nt work. Tried several DIP configuration. When I click "Electonic ID", sometimes it show me "-----" and sometime it show "Sanyo", but never an AT29c256.
I think I've setup burner properly, jump pin #3 and #31, when I test hardware, it show "hardware present". When I try to programm chip, I got an error: "Write sector 0"
The chip was already burned on another burner (don't know wich one) and it work on my car. Just want to put a new .bin on it, but I can't program chip.
Do you have an idea what i'm doing wrong? Or maybe burner is not working properly? Could you tell me if there is something to do to test burner?
For the moment, I got only 1 chip, so I can't test with another one...
Thanks
I tried to switch Willem to PCB3, did'nt work. Tried several DIP configuration. When I click "Electonic ID", sometimes it show me "-----" and sometime it show "Sanyo", but never an AT29c256.
I think I've setup burner properly, jump pin #3 and #31, when I test hardware, it show "hardware present". When I try to programm chip, I got an error: "Write sector 0"
The chip was already burned on another burner (don't know wich one) and it work on my car. Just want to put a new .bin on it, but I can't program chip.
Do you have an idea what i'm doing wrong? Or maybe burner is not working properly? Could you tell me if there is something to do to test burner?
For the moment, I got only 1 chip, so I can't test with another one...
Thanks