TurboEDIT Support (OBD0) - Current Verison: 2.6.x
#116
Re:TurboEdit 1.29
<--- very excited to try out 2.0
Installed a PS9 on Dustins car tonight using TE. (NA version) Your Editor rocks Jason! The ability to edit the multipliers came in very handy.
I used a 3bar along with his 450's and then manually edited the NA maps to reflect the voltage curve the 3bar provided. So far so good. 2000-3200 stumbles a bit between 10hg and 0, but boost transition is good. The goal was to get around the georgehack hiccups.
Any guesses as to what the scales are for the boosted tables on the new boost rom? Like does it start at 0hg and ramp up to 11psi? Is it linear?
Installed a PS9 on Dustins car tonight using TE. (NA version) Your Editor rocks Jason! The ability to edit the multipliers came in very handy.
I used a 3bar along with his 450's and then manually edited the NA maps to reflect the voltage curve the 3bar provided. So far so good. 2000-3200 stumbles a bit between 10hg and 0, but boost transition is good. The goal was to get around the georgehack hiccups.
Any guesses as to what the scales are for the boosted tables on the new boost rom? Like does it start at 0hg and ramp up to 11psi? Is it linear?
#117
Re:TurboEdit 1.29
works pretty well....but its being a bitch at 19inHg (when cruzing at say 70mph) its fine with your foot on the gas a bit, but take it off a nut hair it hits the retarded timing ---- and slows down fast...sorry if that doesnt make sence need some sleep...
Jason, like Dave said im using the PS9...and as i was suspecting code 19.. how do you fix that? besides adding an auto tranny :P
Jason, like Dave said im using the PS9...and as i was suspecting code 19.. how do you fix that? besides adding an auto tranny :P
#118
Re:TurboEdit 1.29
Wait, so I can boost higher with a 3bar and turbo edit? I'm so confused about this stuff, but I don't want to only boost 10psi on my built motor.
I'm still gonna send my ps9 to you. I just figure I'll get a better map from 2.0? WTF do I know?
I'm still gonna send my ps9 to you. I just figure I'll get a better map from 2.0? WTF do I know?
#120
Re:TurboEdit 1.29
no, im under the impression that Dave set it up with the 3bar so it would be easier for him to run boost cuz the boost code isnt fully worked out on the TE?? it will still only go to ~10psi cuz thats as far as the map goes (the resolution is too small)...
anyway *update* this thig is being ------ homo!!! on top of that annoyance with my cruzing speed ----, its hella gay at like 3.5k+ area and will buck like a ----------er. then just a minute ago on the way home it wont rev past 2K it its life depended on it in any gear (luckly its midnight and there is no one on the road). after running around with my head cut off for a minute i deside to shut the car off and see if it will start, then throw the Zdyne back in (still behind my seat), but it fires up fine and revs to 4k (where the launch contorl is set at) i drive for a little further down the road and realize it was probly throwing a code (its throwing a 19 all the time) i check and its throwing a code 3 anyway i think this needs a little more work on it....
anyway *update* this thig is being ------ homo!!! on top of that annoyance with my cruzing speed ----, its hella gay at like 3.5k+ area and will buck like a ----------er. then just a minute ago on the way home it wont rev past 2K it its life depended on it in any gear (luckly its midnight and there is no one on the road). after running around with my head cut off for a minute i deside to shut the car off and see if it will start, then throw the Zdyne back in (still behind my seat), but it fires up fine and revs to 4k (where the launch contorl is set at) i drive for a little further down the road and realize it was probly throwing a code (its throwing a 19 all the time) i check and its throwing a code 3 anyway i think this needs a little more work on it....