installed my chipped p28 and 450s - now car barely runs
#11
Re: installed my chipped p28 and 450s - now car barely runs
a friend came over with a chipped p28 equivilent from the same person, with a map for the same motor with the same injectors with a t25, pluged it in my car started right up.
we put his chip in my ecu and it did not run. we put my chip in his ecu and it ran like ----. so my ecu is messed up and my chip has a bad map. tryin to contact the seller now
we put his chip in my ecu and it did not run. we put my chip in his ecu and it ran like ----. so my ecu is messed up and my chip has a bad map. tryin to contact the seller now
#12
Re: installed my chipped p28 and 450s - now car barely runs
what car is this in? I just finished installing uberdata in my 96 civic and the base map that was supposed to be good wouldn't run my car at all, it was waaayyyyy too lean. every engine is different. try and get ahold of a wideband and definitely get a burner. maybe it just needs a good tuning.
Mark
Mark
#14
Re: installed my chipped p28 and 450s - now car barely runs
Originally Posted by WTF
its in a 96 coupe y8, my friend that brought his ecu has the same car and motor
#15
Re: installed my chipped p28 and 450s - now car barely runs
Just because your freind has a y8 also doesn't mean they're going to have the same tune. I had to drastically change a normal basemap for a Y7 on mine just to get it to run. If it starts up but just kind of dies off, like mine did, you need to check the fuel and the timming. make sure the base timing on your map is set to 12.50 not 16.50, the y7 and y8 are at 12 degrees btdc while obd1 d series are 16 degrees btdc(correct me if i'm wrong). you might not be getting enough fuel either. like i said i had to richen my base map like 20 points in uberdata before it would even run. try to get a wideband or at least an afr guage and you really need to just buy a burner so you can tune the thing yourself. hope you work it out man.
Mark
Mark
#16
Re: installed my chipped p28 and 450s - now car barely runs
they were both un-tuned basmaps by the same person. all i know is my car ran on his ecu and chip, but no other comanation of my ecu/chip and his. so my ecu and chip were the problem. it was sent back to cray today hopefully he can fix it up or replace it asap.
#17
Re: installed my chipped p28 and 450s - now car barely runs
solid process of elimination work getting the issues figured out.
strange that the chip and the ecu both didnt work...
either way, cray will get you set up, he's sharp.
strange that the chip and the ecu both didnt work...
either way, cray will get you set up, he's sharp.
#18
Re: installed my chipped p28 and 450s - now car barely runs
I run the ECU's through my car b4 I sell em, makes sure the ECU's are good. It is almost always a chip problem, or a user error type thing.
I will get it done this weekend for ya. Been working all week.
I will get it done this weekend for ya. Been working all week.
#20
Re: installed my chipped p28 and 450s - now car barely runs
Originally Posted by WTF
cray - you get that ecu out yet? i PM'd and gave u a call... without a car here...
It turns out someone tried to do a O2 sensor mod on the ECU. Put the trans in backwards. No sticker on the outside, so I assumed that it was a P06. (:1 should have looked to be sure) So I am guessing that is why it wouldn't run very well for you.
Thanks again for blowing up my inbox on 2 sites, calling my phone, and sending an e-mail. Nothing people love more than that all in the same day. Makes ya feel loved when you get back from your 9-5 job.
Thread
Thread Starter
Forum
Replies
Last Post
baker_jeff
Forced Induction
8
07-05-2006 07:25 PM
Turblow
Forced Induction
7
06-30-2006 11:27 AM
crx2fast
General Discussion
0
06-29-2006 09:51 PM
Honda16hb
Engine Management
21
12-19-2004 01:59 PM
Sirex
Turbo Parts For Sale
1
01-07-2004 12:02 AM