ZC Race Parts, Air-water IC, Slicks, T3/T4 other shiet
09-16-2003, 03:54 PM
#1
Administrator
Thread Starter
Join Date: Dec 2002
Posts: 13,991
ZC Race Parts, Air-water IC, Slicks, T3/T4 other shiet
Time to clean the garage and get rid of some of this ---- I have laying around. All of these items will be offered locally first, if nobody jumps on them... They are all going on ebay 
-Custom B-series Turbo Manifold will Fit B16/B18/B20 w/ Tial35/Delta wastegate flange $200 SOLD!!!!!
-Deltagate MarkII Wastegate spring set at 5.5 psi, and can be cranked up to 12psi. Does have some small damage on the cap. nothing major, works fine.. included is a small 1 1/2 dump tube.$100
-Stainless Steel Equal Length Race manifold for D-series / T4 Turbo setup. this was going to be used on my race car, that I bailed on. Comes with a lower support bracket as well. (note tial 40 flange not included) $500
-Custom ZC Race Intake manifold, basically its a Stock ZC intake manifold chopped off at the flange, and custom runners and plenum welded on. Included is a Bored out GM Ls6 78mm Throttle Body. TPS included. Specs were used from the STR/Venom Manifold for this build. $350
-Custom Air-Water Intercooler Kit, Saab IC with a Professionaly Aluminum box welded around the IC. Pressure tested (no leaks) 2 aluminum fittings also installed. 11in Wide x 10in Tall x 4.5in Deep. Included in the kit is a brand new Shurflow Water pump 3.3gpm & a 1gallon Jazz fuel cell with -10 an fittings. $300
-Honda Crx DX D15b2 shortblock w/ 100k miles on it, came out of a running car, as-is.. (alternator included!) $30 SOLD
-Honda Crx HF D15b6 longblock (blown engine) DT is that a Piston has a hole in it. Rebuildable core, Included Intake manifold/Tranny/Starter/Alternator etc.. (everything shown in pic) $40
-M&H 22x8.0 Slicks w/ Gunmetal Lenso tomcat drag wheels. Plenty of rubber left! (honda/vw 4x100) $250
manifold/wastegate/engine not included
-Turbo/Downpipe T3/04e Turbo .52 Trim .50comp/.63ex w/ 2.5 Downpipe (smashed) Turbo has been through tons of abuse, and is in need of a rebuild. it still works, it does leak a little bit of oil from the exhaust seal. But boosts just fine. This turbo is great for any b or d series project. $350
You can PM me, or Email me.. either way works Jeff@homemadeturbo.com
Jeff
-Custom B-series Turbo Manifold will Fit B16/B18/B20 w/ Tial35/Delta wastegate flange $200 SOLD!!!!!
-Deltagate MarkII Wastegate spring set at 5.5 psi, and can be cranked up to 12psi. Does have some small damage on the cap. nothing major, works fine.. included is a small 1 1/2 dump tube.$100
-Stainless Steel Equal Length Race manifold for D-series / T4 Turbo setup. this was going to be used on my race car, that I bailed on. Comes with a lower support bracket as well. (note tial 40 flange not included) $500
-Custom ZC Race Intake manifold, basically its a Stock ZC intake manifold chopped off at the flange, and custom runners and plenum welded on. Included is a Bored out GM Ls6 78mm Throttle Body. TPS included. Specs were used from the STR/Venom Manifold for this build. $350
-Custom Air-Water Intercooler Kit, Saab IC with a Professionaly Aluminum box welded around the IC. Pressure tested (no leaks) 2 aluminum fittings also installed. 11in Wide x 10in Tall x 4.5in Deep. Included in the kit is a brand new Shurflow Water pump 3.3gpm & a 1gallon Jazz fuel cell with -10 an fittings. $300
-Honda Crx DX D15b2 shortblock w/ 100k miles on it, came out of a running car, as-is.. (alternator included!) $30 SOLD
-Honda Crx HF D15b6 longblock (blown engine) DT is that a Piston has a hole in it. Rebuildable core, Included Intake manifold/Tranny/Starter/Alternator etc.. (everything shown in pic) $40
-M&H 22x8.0 Slicks w/ Gunmetal Lenso tomcat drag wheels. Plenty of rubber left! (honda/vw 4x100) $250
manifold/wastegate/engine not included
-Turbo/Downpipe T3/04e Turbo .52 Trim .50comp/.63ex w/ 2.5 Downpipe (smashed) Turbo has been through tons of abuse, and is in need of a rebuild. it still works, it does leak a little bit of oil from the exhaust seal. But boosts just fine. This turbo is great for any b or d series project. $350
You can PM me, or Email me.. either way works Jeff@homemadeturbo.com
Jeff
Thread
Thread Starter
Forum
Replies
Last Post
95civicLX
General Discussion
8
11-21-2006 09:56 PM
Civic4Sale
Forced Induction
2
08-27-2004 08:12 AM
sean88accord
Forced Induction
2
05-12-2004 11:30 PM
willahlborn
Forced Induction
1
10-24-2003 04:02 PM
