Re: my setup and build pics,will be update as i progress
 

yea can't till its done. im gonna be using crome pro. i may switch to hondata s300 later but for now this will do.......im poor :-\

Re: my setup and build pics,will be update as i progress
 

ya im putting crowers in my b16 also and the clearances didnt like the greens.
I believe the crowers are modeled after the #1 rod.
So now im using 3 yellow sets and 1 pink.

Re: my setup and build pics,will be update as i progress
 

with aftermarket rods they should all be uniform its your rod journals that have the differnce in clearance from one rod to the next. did you micro polish the crank?

Re: my setup and build pics,will be update as i progress
 

my crank is CCCB for the rods
yellow yellow yellow pink

Re: my setup and build pics,will be update as i progress
 

checked all the clearances again with the new honda pink bearings.everything is good. lube that bitch up lets go!http://www.we-todd-did-racing.com/we...EzZGZkMzF5NTQx

roll it over a couple times and everything feels good.

on to o-ringing.

-heat the copper wire for 3 minutes @ 250 degrees this process is called annealing. this will make it more pliable and easier to manipulate.

-start at the very center of the intake side feed the wire into the channnel by hand http://www.we-todd-did-racing.com/we...EzZGZkMzF5NTQx

-then gently tap the wire into the channel with the bottom of a hammer, i opted for my bling bling snap on hammer because of the rubber handle so it won't hurt the wire.http://www.we-todd-did-racing.com/we...EzZGZkMzF5NTQx
http://www.we-todd-did-racing.com/we...EzZGZkMzF5NTQx

-once you get it all into the channel and back around you need to snip it very close so the two ends touch but don't overlap. it has to be perfect and seemless. you will catch on after 2-3 tries. there MUST BE NO GAP OR OVERLAP of the wire. end cutters work best to cut the wirehttp://www.we-todd-did-racing.com/we...EzZGZkMzF5NTQx

-repeat for the other cylinders in the same order. your final product should look like this

http://www.we-todd-did-racing.com/we...EzZGZkMzF5NTQx
http://www.we-todd-did-racing.com/we...EzZGZkMzF5NTQx

Re: my setup and build pics,will be update as i progress
 

dude im loven the step by step helps out alot ceap it comin

Re: my setup and build pics,will be update as i progress
 

Looks great.That should be a real solid setup for boost.When is this beast going back in the car?

Re: my setup and build pics,will be update as i progress
 

i hope to have everything complete by mid june. im playing hurry up and wait with the body shop so........... once i get my car back i can part the motor and swap the head on to here, i've already ported the head on the old motor and my arp head studs are in the old motor too so i'll swap those over. still have to get a water pump, t belt, some misc. orings and ----.

Re: my setup and build pics,will be update as i progress
 

one new pic. i think im going to jb weld a -10 an bung where the crankase ventilation hole is and run it to a catch can and the other bung on the catch can to the exh. slash cut. anyways still waiting on parts.

http://www.we-todd-did-racing.com/we...EzZGZkMzF5NTQx

Re: my setup and build pics,will be update as i progress
 

noice noice niceee! O0