HomemadeTurbo - DIY Turbo Forum

HomemadeTurbo - DIY Turbo Forum (https://www.homemadeturbo.com/)
-   General Discussion (https://www.homemadeturbo.com/general-discussion-6/)
-   -   Advise me on riceboy bodywork for my car. (https://www.homemadeturbo.com/general-discussion-6/advise-me-riceboy-bodywork-my-car-84225/)

ryan89crx 09-24-2007 01:30 PM

Re: Advise me on riceboy bodywork for my car.
 
id go with the 88-89 CRX front bumper. it doesnt cut so far back and, although it does require trimming, it wont stick out like the picture you have drawn

abnaasefmb 09-24-2007 02:35 PM

Re: Advise me on riceboy bodywork for my car.
 
91 si bumper cover, i had to do some cutting, and getto mesh. oh and i trimmed the bumper support. :8
http://www.we-todd-did-racing.com/fi...p/IMG_2507.JPG
http://www.we-todd-did-racing.com/fi...h/IMG_2508.JPG

RotaryGeek 09-24-2007 02:38 PM

Re: Advise me on riceboy bodywork for my car.
 
+1 its a little more work but it would look a lot better than a body kit or someother gay ----. crx ftw.

Tom-Guy 09-24-2007 03:06 PM

Re: Advise me on riceboy bodywork for my car.
 
Sweet, Mike, that's exactly what I'm looking for!

What size was your IC, again?

abnaasefmb 09-24-2007 03:15 PM

Re: Advise me on riceboy bodywork for my car.
 
i think the same. its a jonnyrace. i'll email you some pics tomorrow, i'm in iraq so my net speed is less that dial-up :l

Tom-Guy 09-24-2007 03:18 PM

Re: Advise me on riceboy bodywork for my car.
 
Sweet, I appreciate it. Be safe over there.

abnaasefmb 09-24-2007 03:30 PM

Re: Advise me on riceboy bodywork for my car.
 
Lol, I’m a frequent flyer at this point, in the last five years I’ve been here more an NC :6

reactone 09-24-2007 03:35 PM

Re: Advise me on riceboy bodywork for my car.
 
Too bad water/meth injection was deemed unsuitable. :(

Hitchhikkr 09-24-2007 03:45 PM

Re: Advise me on riceboy bodywork for my car.
 

Originally Posted by reactone
Too bad water/meth injection was deemed unsuitable. :(

water injection wasnt deemed unsuitable. It just doesnt decrease IAT's. It DOES do the same thing its always done, which is to raise your knock limit with pump gas. JD's car will see a steady diet of race fuel. water injection not required.

JD, I think we need to go in on a few 55gal drums of race gas, and stash it somewhere closeby...

Tom-Guy 09-24-2007 03:58 PM

Re: Advise me on riceboy bodywork for my car.
 
Water injected knock limit of the 85mm LS should be in the 450-480 whp range. Running an engine right against knock limit is the quickest way to wear it out, and I want 500+. Further, on the street I don't plan to lay down more than 350, unless I'm running slicks in which case it will be strictly racegas power levels. Water injection is pretty pointless for this setup.


All times are GMT -5. The time now is 07:34 PM.


© 2024 MH Sub I, LLC dba Internet Brands