? for turbo gods only
04-06-2006, 02:00 PM
#1
0.0 BAR
Thread Starter
Join Date: Mar 2006
Posts: 10
? for turbo gods only
fellas, you've been a big help so far.
got a question for you. i'm piecing together a turbo kit for my saturn and i'm using the T25 2nd gen. want around 210hp. figure 290cc/min will do it at 8psi if i run the pressure from the walbro up a bit.
i read the thread on here about which turbo's wastegate vents at which pressure and some of you have been kind enough to give me a direct answer but i got another question.
in alldata (time guide I use at our shop), the spec says the rod for the wastegate should move at 6.8 psi. i've verified that it does start to move at that psi with a pressure tester.
you guys told me that it vents at 8 psi but will go up to 10 or so with what the factory mitsu vehicle's EBC makes it to do.
question...
not real clear on how the EBC for the stock mitsu controls. does it control the 8psi and then up to 10 on certain conditions present, OR, is that wastegate only going to allow me to boost to 8psi without the aid of the EBC from a stock mitsu setup (which is what I want)?
my goal is to run ONLY 8psi due to not wanting to run management for the injectors. because of this, i am stuck with the size i need and not going any larger for startup and cruise problems from too much fueling.
i rely on good info here...help a brutha out.
04-06-2006, 02:04 PM
#2
3.0 BAR
Join Date: Mar 2005
Posts: 3,161
Re: ? for turbo gods only
You set a boost controller and it limits or "bleeds" the vacuum kind of tricking the WG into thinking it's at 8psi or whatever it's stock setting is and it actually is a higher amount. I'm a little confused on your question though. 
JP
JP
04-06-2006, 02:19 PM
#3
Guest
Posts: n/a
Re: ? for turbo gods only
Originally Posted by samson
You set a boost controller and it limits or "bleeds" the vacuum kind of tricking the WG into thinking it's at 8psi or whatever it's stock setting is and it actually is a higher amount. I'm a little confused on your question though.
JP
JP
To answer the OP's question, without the mitsu ebc, your turbo will boost 6.8 psi with the stock wastegate. The ebc is an addition that makes the wastegate raise the boost a bit. Without the ebc, you will boost what the wastegate itself it set at, which is 6.8 psi. If you want 8 psi, get a manual boost controller to slightly restrict the air going to your wastegate's vaccuum port.
04-06-2006, 03:10 PM
#4
1.0 BAR
Join Date: Oct 2004
Posts: 623
Re: ? for turbo gods only
Originally Posted by saturnfan
... if i run the pressure from the walbro up a bit.
... i am stuck with the size i need and not going any larger for startup and cruise problems from too much fueling.
... i am stuck with the size i need and not going any larger for startup and cruise problems from too much fueling.
04-06-2006, 04:01 PM
#6
0.0 BAR
Thread Starter
Join Date: Mar 2006
Posts: 10
Re: ? for turbo gods only
yeah, i reread that post and it takes a genius to figure it out. i'll do better next time.
i think jagojon figured out what I was trying to ask.
and yes, i'm going to use the begi rrfpr. i didn't mean to leave that out.
you guys are great. thanks again!!!
i think jagojon figured out what I was trying to ask.
and yes, i'm going to use the begi rrfpr. i didn't mean to leave that out.
you guys are great. thanks again!!!
Thread
Thread Starter
Forum
Replies
Last Post
