IntegraXSi

What all do I need to run the oil lines.. I am going to run SS line.. This is B18B T3/T4 set up.. What I want to do is shop around see how much to buy all the stuff or should i just but a Oil line "kit" this is to an from the turbo.. also have to buy some flanges were are the best places? Thanks

HMT-Admin

What flanges do you need? cheapturbo has some b-series head flanges along with some Garrett flanges.

Oil line.. Well the thread pitch is 1/8bsp off the back off the block, I would recommend getting a 1/8bsp to 1/8npt fitting, then going into a 3way splitter 1/8npt. Run oil pressure off one, inlet to the other and a 1/8 to -an4 on the feed line. Run that to your turbo (which should be also a 1/8npt line) so get 2 1/8th to -an 4's. Probably need about 4ft of -an line

Piece of cake.

Jeff

shortyz

holy fuckshit jeff we need a stickies post on oil lines

http://www.honda-tech.com/zerothread?id=373528&page=2 - chipping
http://www.honda-tech.com/zerothread?id=366319 - clutch install
http://www.honda-tech.com/zerothread?id=67146 -oil return
http://www.honda-tech.com/zerothread?id=109160 -oil return line setup
http://www.honda-tech.com/zerothread?id=114490 -oil return line parts
http://www.honda-tech.com/zerothread?id=71999 -where to weld oil return
http://www.honda-tech.com/zerothread?id=119100 -oil return line
http://www.honda-tech.com/zerothread?id=119539 -oil pan welding
http://www.honda-tech.com/zerothread?id=119715 -oil pan welding
http://www.honda-tech.com/zerothread?id=118687 -oil grade to use
http://www.honda-tech.com/zerothread?id=118694 -ft for oil feed line
http://www.honda-tech.com/zerothread?id=118807 -oil feed line
http://www.honda-tech.com/zerothread?id=119681 -oil feed line
http://www.honda-tech.com/zerothread?id=93550 -part for oil feed line
http://www.honda-tech.com/zerothread?id=114436 -where to buy brass t for feed line
http://www.honda-tech.com/zerothread?id=126335 -oil t question
http://www.honda-tech.com/zerothread?id=125438 -another place to buy oil lines
http://www.honda-tech.com/zerothread?id=131447 -oil feed line an/npt connector ?
http://www.honda-tech.com/zerothread?id=134078 -feed diagram
http://www.honda-tech.com/zerothread?id=133948 -oil bpst fitting again
http://www.honda-tech.com/zerothread?id=144586 -oil feed line restrictor
http://www.honda-tech.com/zerothread?id=155510 -oil leaks
http://www.honda-tech.com/zerothread?id=158018 -oil feed 3' better
http://www.honda-tech.com/zerothread?id=156571 -oil pan bolts
http://www.honda-tech.com/zerothread?id=170223 -oil pressure readings
http://www.honda-tech.com/zerothread?id=168084 -oil feed fitting
http://www.honda-tech.com/zerothread?id=131450 -oil feed diagram
http://www.honda-tech.com/zerothread?id=195068 -oil pressu
http://www.honda-tech.com/zerothread?id=364948 -BSPT and NPT AN explanation. ***