HomemadeTurbo - DIY Turbo Forum
Page 2 of 3
1
2
3
Show 40 post(s) from this thread on one page

HomemadeTurbo - DIY Turbo Forum (https://www.homemadeturbo.com/)
-   Forced Induction (https://www.homemadeturbo.com/forced-induction-7/)
-   -   m43 garrett should i run restrictor for oil feed line (https://www.homemadeturbo.com/forced-induction-7/m43-garrett-should-i-run-restrictor-oil-feed-line-94904/)

ndnnikk 09-01-2008 07:00 PM
Re: m43 garrett how much hp is this rated for
 
Thankx bro you've been alot of help.

da_dude 09-02-2008 02:52 AM
Re: m43 garrett how much hp is this rated for
 
It's a t3/t04b. From what I gather up it's t3/t04b H-trim. I measure the trim and it came to 58mm on the inducer on the compressor wheel.

crx2211 09-02-2008 07:10 AM
Re: m43 garrett how much hp is this rated for
 
Originally Posted by da_dude
It's a t3/t04b. From what I gather up it's t3/t04b H-trim. I measure the trim and it came to 58mm on the inducer on the compressor wheel.
To4b doesn't come in .70 a/r. Only .50 a/r and .60 a/r. It's a T3/TO4E. Trim isn't measured in mm. 58mm sounds about right though for the inducer of the compressor wheel.

da_dude 09-03-2008 02:13 AM
Re: m43 garrett how much hp is this rated for
 
You sure? My t3/t04e 46 trim turbo looks way bigger than the same turbo picture above. Well, at least the front compressor housing is. The t3/t04e front compressor housing with a .70 a/r housing would likely have a 4 inch inlet and 2 1/2 inch outlet on the compressor. While the snail above is probably a 2.75-3 inch inlet to a 2 inch outlet on the t3/t04b compressor side. I know my t3/t04b H-trim /w the .70 ar compressor housing have a 2.75 inch inlet with a 2 inch outlet. But nonetheless, it's still a good turbo.

crx2211 09-03-2008 04:46 PM
Re: m43 garrett how much hp is this rated for
 
Originally Posted by da_dude
You sure? My t3/t04e 46 trim turbo looks way bigger than the same turbo picture above. Well, at least the front compressor housing is. The t3/t04e front compressor housing with a .70 a/r housing would likely have a 4 inch inlet and 2 1/2 inch outlet on the compressor. While the snail above is probably a 2.75-3 inch inlet to a 2 inch outlet on the t3/t04b compressor side. I know my t3/t04b H-trim /w the .70 ar compressor housing have a 2.75 inch inlet with a 2 inch outlet. But nonetheless, it's still a good turbo.
I am sure. The .60 a/r TO4E housing is actually slightly larger (outer diameter) even though it's not .70 a/r. The .70 a/r TO4E has a larger inlet though. The 4" inlet is a .70 a/r TO4S cover. This turbo is a .70 a/r TO4E.

Slo_crx1 09-07-2008 06:59 PM
Re: m43 garrett how much hp is this rated for
 
That turbo's decent sized, but like crx2211 said, it's definitely not a 4" inlet found on the To4S covers. I dunno about the .82 a/r though, that seems like a peak power maker to me with no balls down low. I'd honestly rather have a .63 housing for a d16 but that's just me. :P

ndnnikk 09-10-2008 09:21 PM
Re: m43 garrett how much hp is this rated for
 
where do i get 63 housing from

crx2211 09-10-2008 09:23 PM
Re: m43 garrett how much hp is this rated for
 
Originally Posted by ndnnikk
where do i get 63 housing from
New they're about $200. Used can be had as cheap as $60-$100 for the stage 3 one you'll need.

da_dude 09-13-2008 11:39 PM
Re: m43 garrett how much hp is this rated for
 
The h-trim and the 57 trim both flow at 49 lbs/min.

vortecfiero 09-14-2008 11:16 PM
Re: m43 garrett how much hp is this rated for
 
Originally Posted by crx2211
New they're about $200. Used can be had as cheap as $60-$100 for the stage 3 one you'll need.
is there a larger AR than .82 for the T31?
i have boost at 2300 rpm and im concerned that at 5000 rpm it might be choking it (I dont know what turbine wheel i have)


All times are GMT -5. The time now is 02:30 AM.
Page 2 of 3
1
2
3
Show 40 post(s) from this thread on one page


© 2024 MH Sub I, LLC dba Internet Brands