m43 garrett should i run restrictor for oil feed line
 

Attachment 15023
Attachment 15024
Attachment 15025
Attachment 15026
http://i8.photobucket.com/albums/a4/...etturbo001.jpg

D16Z6 vitara's, tuner toy rods, 450cc blue tops, ebay cast t3 manifold, turbonetics delgate wastegate, dsm 1g blow off valve, aem fuel rail, aem fpr, 62mm tb, ebay intercooler, obx lsd. Turbo is from 03 ford powerstroke. Is this turbo to big for my set up?

Re: Has anyone used this turbo for D16z6
 

im not too sure, but if it is extrnally gated shouldn't you block off that hole for the old wastegate? i may be wrong or your d/p may do it but i was just wondering. but i say use it

Re: Has anyone used this turbo for D16z6
 

need to get 5 bolt flange haven't made down pipe yet flange will have block off

Re: Has anyone used this turbo for D16z6
 

ok thats what i thought/wondering.

Re: Has anyone used this turbo m43 garrett whats the trim size
 

The turbo is perfect, I love high end spool...you'll love it too. Thats a good size :y

Just go 3" open downpipe and with the bigger injectors you could go alot faster safely.

Re: Has anyone used this turbo m43 garrett whats the trim size
 

It's a .70 a/r TO4E cover. Looks to be a T31 turbine wheel. Compressor is probably around 56-59mm. That would make it a 50 or 57 trim most likely; probably 57. I'd have to research to find out for sure though. I have the same exact turbo here at my house that I forgot about until I saw this thread lol. Now I'm stoked because I have a sweet turbo around that I can sell off or trade or use.

Re: Has anyone used this turbo m43 garrett whats the trim size
 

HOUSESHOES FTW NIGGA!!!

Re: Has anyone used this turbo m43 garrett whats the trim size
 

I have the exact same turbo but with the .63 ar turbine housing instead of the .82 ar housing. I will using it got my build d16z6 also.

Re: Has anyone used this turbo m43 garrett whats the trim size
 

is this a laggy turbo? Can i put smaller exhaust housing on there thats a direct swap

Re: Has anyone used this turbo m43 garrett whats the trim size
 

The T31 (aka stage 3) isn't too laggy. Down really low in the rev range that turbo won't do much, but it's nice up top and in the middle. It has pretty much the exact same wheel specifications as the PTE SC34. So yes, your turbo is a 57 trim. If you want to go to a smaller turbine housing (probably a good idea) you'll just have to find a turbine housing that can accommodate the stage 3 turbine wheel. Some of the turbos came with a slightly smaller 69 trim turbine wheel as opposed to the 76 trim T31 turbine wheel, so you'll have to measure it to make sure. .48 a/r or .63 a/r are both good sizes.

Re: m43 garrett how much hp is this rated for
 

Thankx bro you've been alot of help.

Re: m43 garrett how much hp is this rated for
 

It's a t3/t04b. From what I gather up it's t3/t04b H-trim. I measure the trim and it came to 58mm on the inducer on the compressor wheel.

Re: m43 garrett how much hp is this rated for
 

To4b doesn't come in .70 a/r. Only .50 a/r and .60 a/r. It's a T3/TO4E. Trim isn't measured in mm. 58mm sounds about right though for the inducer of the compressor wheel.

Re: m43 garrett how much hp is this rated for
 

You sure? My t3/t04e 46 trim turbo looks way bigger than the same turbo picture above. Well, at least the front compressor housing is. The t3/t04e front compressor housing with a .70 a/r housing would likely have a 4 inch inlet and 2 1/2 inch outlet on the compressor. While the snail above is probably a 2.75-3 inch inlet to a 2 inch outlet on the t3/t04b compressor side. I know my t3/t04b H-trim /w the .70 ar compressor housing have a 2.75 inch inlet with a 2 inch outlet. But nonetheless, it's still a good turbo.

Re: m43 garrett how much hp is this rated for
 

I am sure. The .60 a/r TO4E housing is actually slightly larger (outer diameter) even though it's not .70 a/r. The .70 a/r TO4E has a larger inlet though. The 4" inlet is a .70 a/r TO4S cover. This turbo is a .70 a/r TO4E.

Re: m43 garrett how much hp is this rated for
 

That turbo's decent sized, but like crx2211 said, it's definitely not a 4" inlet found on the To4S covers. I dunno about the .82 a/r though, that seems like a peak power maker to me with no balls down low. I'd honestly rather have a .63 housing for a d16 but that's just me. :P

Re: m43 garrett how much hp is this rated for
 

where do i get 63 housing from

Re: m43 garrett how much hp is this rated for
 

New they're about $200. Used can be had as cheap as $60-$100 for the stage 3 one you'll need.

Re: m43 garrett how much hp is this rated for
 

The h-trim and the 57 trim both flow at 49 lbs/min.

Re: m43 garrett how much hp is this rated for
 

is there a larger AR than .82 for the T31?
i have boost at 2300 rpm and im concerned that at 5000 rpm it might be choking it (I dont know what turbine wheel i have)

Re: m43 garrett how much hp is this rated for
 

Not that I'm aware of. I think any larger than .82 and you'll be looking at a T4 housing. Sure there are T3 flanged turbine housings that are way larger than .82 a/r, but they sure don't accept the T31 turbine.