I read above, but need help... B18c5 turbo setup
#11
Re: I read above, but need help... B18c5 turbo setup
Originally Posted by naudlee
Currently it runs like 185whp with I/E/H/ and chipped obd1 ecu.
#12
Re: I read above, but need help... B18c5 turbo setup
i had a itr turbo...jack at p1 neptuned it...it was a stout little car...the setup was
Full-Race t3/t67 turbo
CrpManifold
Crp 2.5” Intercooler Piping
Crp Dumptube
Crp 3” Downpipe
Tial 50mm Bov
Tial 44mm Wastegate w/ V-Band
Precision 600hp Intercooler 31.5x8x3.5
it made like 270whp on a mustang dyno...we turned the boost up and ended up blowing the motor...i have the turbo with a fresh rebuild on it if you're intrested
Full-Race t3/t67 turbo
CrpManifold
Crp 2.5” Intercooler Piping
Crp Dumptube
Crp 3” Downpipe
Tial 50mm Bov
Tial 44mm Wastegate w/ V-Band
Precision 600hp Intercooler 31.5x8x3.5
it made like 270whp on a mustang dyno...we turned the boost up and ended up blowing the motor...i have the turbo with a fresh rebuild on it if you're intrested
#13
Re: I read above, but need help... B18c5 turbo setup
if I can figur eout how to upload the dyno sheet, as in borrow a cam, I'll show you. Its beenf inely tuned. ^And about your turbo, you still have all piping and everything or just the snail itself,not the kit?
#16
Re: I read above, but need help... B18c5 turbo setup
if you are even thinking about building the bottom end, just get yourself a gsr or LS and boost it. Dont mess with the bottom end of an ARRrr unless its higher compression, forged pistons and rods, for some serious NA power.
#17
Re: I read above, but need help... B18c5 turbo setup
my GSR made 166 whp with dc header, aem cai, cat back exhaust, ctr ecu (stock obd2) and a skunk 2 intake mani.... sooo i believe his itr could make a lot more than 150 whp...but 185, i would have to see the dyno chart as well to believe, in the low 170's....maybe....
#19
Re: I read above, but need help... B18c5 turbo setup
thanks, I'm not lying about the 185whp, why would I lie abotu such a small number, I'd atleastr make it saucy and go with 200+, ahaha. I'll try and find a scanner to put up the dyno sheets. I have more than just I/H/E, I'm running USDM b18c5 block w/ JDM itr head, AEM cai, Unorthodox racing underdrive pulley, no ac, custom made piping with RS*R exhaustsystem fromthe cat back, obd1 ecu that was chipped precisely tuning on a dyno, blah blah lots of other junk aswell... (if you haven't noticed already my typing sucks, and my wording aswell) All in a 99 civic hatch, full ITR interior, GSR cluster swapped in there, nothing liek it aroudn here, no ones keeps it nice and JDM, too many rice boys , we could have a rice farm where I'm at, but its perty and I like perty.
#20
Re: I read above, but need help... B18c5 turbo setup
Originally Posted by naudlee
I have more than just I/H/E, I'm running USDM b18c5 block w/ JDM itr head, AEM cai, Unorthodox racing underdrive pulley, no ac, custom made piping with RS*R exhaustsystem fromthe cat back, obd1 ecu that was chipped precisely tuning on a dyno,
What header?
Thread
Thread Starter
Forum
Replies
Last Post
canadianmade
General Discussion
0
06-01-2005 11:36 AM
94geeser
Engine Management
4
06-13-2004 06:26 PM