HomemadeTurbo - DIY Turbo Forum
Page 3 of 10
1
2
3
4
5
6
7
8
9
10
Show 40 post(s) from this thread on one page

HomemadeTurbo - DIY Turbo Forum (https://www.homemadeturbo.com/)
-   Forced Induction (https://www.homemadeturbo.com/forced-induction-7/)
-   -   Do you like xs/ebay turbos/parts?? (https://www.homemadeturbo.com/forced-induction-7/do-you-like-xs-ebay-turbos-parts-87295/)

97spydagst 12-24-2007 02:47 PM
Re: Do you like xs/ebay turbos/parts??
 
here a vid i put together of my buddys dynoing there cars
http://www.mydeo.com/videosavecopy.asp? ... CID=150240 both are using cheap mani's and the single is using the full kit..we did notice on the dyno with more boost he made less power,and the intercooler heated up very fast.

Slo_crx1 12-24-2007 03:02 PM
Re: Do you like xs/ebay turbos/parts??
 
Originally Posted by 97spydagst
slo_crx i understand what your saying if i had a 30k car i wouldnt use this stuff cause having a car like that means i can afford nice parts.. but most of us just have normal 0-8k cars that we play with and mod on low funds.. If i had a full race car would i use most of it NO but i was just asking for the averge guy if they run/like xs power stuff.
I completely understand what you're saying. I've used certain chinese parts in the past on cheap builds too.
Originally Posted by junkyg20
Real greddy BOVs are so shitty the knockoffs are usually no worse.
The older Greddy bov's weren't too bad. The newer Type Rs's have issues with the diaphragms over time, they tend to dry rot. That just goes along with common sense, if you know a part's going to fail (even a good name one) you really wouldn't want to spend the money on it.
Originally Posted by 97spydagst
here a vid i put together of my buddys dynoing there cars
http://www.mydeo.com/videosavecopy.asp? ... CID=150240 both are using cheap mani's and the single is using the full kit..we did notice on the dyno with more boost he made less power,and the intercooler heated up very fast.
That's pretty typical with the cheaper cores they use. For low boost they're fine compared to no IC at all, but they heatsoak and lose efficiency pretty fast at higher boost. For most of you guys that's fine, for me specifically where I run 23+psi it's a big no-no.

one2many 12-24-2007 03:08 PM
Re: Do you like xs/ebay turbos/parts??
 

why are you still here when you are so much better then us ? ??? ?

Slo_crx1 12-24-2007 03:20 PM
Re: Do you like xs/ebay turbos/parts??
 
Originally Posted by one2many
why are you still here when you are so much better then us ? ??? ?



Get a life fag. ::) I haven't seen you offer any real information yet other than running your mouth and telling other noobs how great chinese turbos are. :P

one2many 12-24-2007 03:30 PM
Re: Do you like xs/ebay turbos/parts??
 

better none then incorrect/biest like you. ^-^

Slo_crx1 12-24-2007 04:03 PM
Re: Do you like xs/ebay turbos/parts??
 
Originally Posted by one2many
better none then incorrect/biest like you. ^-^

This from the guy that can't even spell "biased" properly. ::) Get back to school young buck. If my information that I post is incorrect, it usually becomes known.

jacer63 12-24-2007 05:01 PM
Re: Do you like xs/ebay turbos/parts??
 
Originally Posted by slo_crx1
Note Jeff Frank's amount of time spent on this site lately noob. There's a good reason for it. Also, I don't own a ghetto-fied junktastic Honda anymore. When I owned my old hatchback I built everything for it, tuned everything on it, did all my own work. I've put my time in on this site and have helped out more people locally and country-wide, and I've seen what works and what doesn't from personal experience, not what some random idiot posts on the web. I've been in the boost game for 10 years, probably right around the time you as a little kid started fingering your ass while drooling over stupid-street magazine.
Would you in all honesty want to use parts that are known to be junk? For your $100 piece of ---- maybe you would, but get real...would you put this crap on a $32,000 car? I think not. And if you had been around when Jeff Frank did his SSAC testing like I was you would see even he said it was junk. I highly suggest you shut up and learn for while before you open your mouth and prove you're an idiot.
what an asshat..^^^ ive been rockin a xs mani with no problems,turbo is holdin up too .runnin 15 psi at times. all i did was ordered a garrett rebuild kit. there kit has chamfered bearingfs. take your 32,000 car and shove it up your ass

Slo_crx1 12-24-2007 06:34 PM
Re: Do you like xs/ebay turbos/parts??
 
Originally Posted by jacer63
what an asshat..^^^ ive been rockin a xs mani with no problems,turbo is holdin up too .runnin 15 psi at times. all i did was ordered a garrett rebuild kit. there kit has chamfered bearingfs. take your 32,000 car and shove it up your ass
---- off dick. It's pukes like you ------ noobs running off the coat tails of people who started boosting Hondas in the beginning that give us and the industry a bad name. I've paid my dues, boosted more cars than your age and IQ combined, and contributed a lot to the Honda community in general. Just because I happen to have a lot of respect for people with innovation isn't a good reason to jump on the band wagon and say I'm an ass hat. The only thing these leaches do is copy other people's hard work and pass off as their own. If the car community as a whole stopped coming out with new parts completely, I guarantee companies like SSautoshit wouldn't have anything new and fantastic to offer either. What happened to people taking pride in their work? Or learning to make their own parts? Do you honestly think that us in the very beginning had any of these junk resources at our fingertips? NO. We had to make what we needed, and make work what we needed. I hope that everyone who runs these pieces of ---- will end up with compressor wheel parts in their motor, maybe then you'll learn your lesson. There is homemade and homemade quality, and there is this junk. By all rights you idiots shouldn't even be on this site, there is nothing homemade about buying a junk kit and tossing it on your car. This ranks up there buying a greddy or edelbrock kit and throwing on your car, but at least they have quality. Let's see your quality and innovation. You are the reason I and many others have no respect for the new generation of Honda tools. So take your junk xs-turblow mani and shove it back up your ass, maybe you'll get lucky and it won't crack once it hits your balls.

Inquisition 12-24-2007 08:51 PM
Re: Do you like xs/ebay turbos/parts??
 
Slo is right. I'm not much of a n00b basher but sooner or later you will come to the conclusion driving around in a decent car you don't have to worry about all the time is worth the extra money. I know I learned that lesson very quickly. Now all I want is a decent daily driver and this:

http://www.superlitecars.com/img_roa...dster_1_fs.jpg

sikcrx89 12-24-2007 09:29 PM
Re: Do you like xs/ebay turbos/parts??
 
Originally Posted by slo_crx1
---- off dick. It's pukes like you ------ noobs running off the coat tails of people who started boosting Hondas in the beginning that give us and the industry a bad name. I've paid my dues, boosted more cars than your age and IQ combined, and contributed a lot to the Honda community in general. Just because I happen to have a lot of respect for people with innovation isn't a good reason to jump on the band wagon and say I'm an ass hat. The only thing these leaches do is copy other people's hard work and pass off as their own. If the car community as a whole stopped coming out with new parts completely, I guarantee companies like SSautoshit wouldn't have anything new and fantastic to offer either. What happened to people taking pride in their work? Or learning to make their own parts? Do you honestly think that us in the very beginning had any of these junk resources at our fingertips? NO. We had to make what we needed, and make work what we needed. I hope that everyone who runs these pieces of ---- will end up with compressor wheel parts in their motor, maybe then you'll learn your lesson. There is homemade and homemade quality, and there is this junk. By all rights you idiots shouldn't even be on this site, there is nothing homemade about buying a junk kit and tossing it on your car. This ranks up there buying a greddy or edelbrock kit and throwing on your car, but at least they have quality. Let's see your quality and innovation. You are the reason I and many others have no respect for the new generation of Honda tools. So take your junk xs-turblow mani and shove it back up your ass, maybe you'll get lucky and it won't crack once it hits your balls.
couldnt have said it any better


All times are GMT -5. The time now is 03:34 AM.
Page 3 of 10
1
2
3
4
5
6
7
8
9
10
Show 40 post(s) from this thread on one page


© 2024 MH Sub I, LLC dba Internet Brands