406whp/281wht Stock Sleeve Turbo D16z6 Video/Dyno Sheet
02-28-2007, 12:09 PM
#41
0.0 BAR
Thread Starter
Join Date: Jul 2003
Posts: 31
Re: 406whp/281wht Stock Sleeve Turbo D16z6 Video/Dyno Sheet
Phearable.net send's customer's the same bins from vehicles that have actually been tuned.
So.... Lets look at some dyno sheets to see how bad the fuel curves look:
Look close for the blue lines:
Wow, those fuel curves sure look flat don't they ?
If I didn't know what I was doing I wouldn't tune cars for a living.
I wouldn't be booked several weeks in advanced at a time, I wouldn't have people driving from southflorida & out of state to have their cars tuned.
This forum is simply filled with a bunch of haters that do not support phearable.net & will go out on a limb to try and make us look bad by jumping on a bashing bandwagon.
So.... Lets look at some dyno sheets to see how bad the fuel curves look:
Look close for the blue lines:
Wow, those fuel curves sure look flat don't they ?
If I didn't know what I was doing I wouldn't tune cars for a living.
I wouldn't be booked several weeks in advanced at a time, I wouldn't have people driving from southflorida & out of state to have their cars tuned.
This forum is simply filled with a bunch of haters that do not support phearable.net & will go out on a limb to try and make us look bad by jumping on a bashing bandwagon.
02-28-2007, 12:11 PM
#42
3.0 BAR
Join Date: Dec 2004
Posts: 1,976
Re: 406whp/281wht Stock Sleeve Turbo D16z6 Video/Dyno Sheet
Originally Posted by mtber
The vehicle was street tuned & the customer put the car on a dynodynamics dyno which reads low.
Anything else you want to try and talk ---- about ?
Anything else you want to try and talk ---- about ?
weird, i made 250whp on a 100% stock GSR with the same turbo @ 7psi, a log manifold on a pig rich tune
02-28-2007, 12:29 PM
#43
0.0 BAR
Thread Starter
Join Date: Jul 2003
Posts: 31
Re: 406whp/281wht Stock Sleeve Turbo D16z6 Video/Dyno Sheet
Originally Posted by ryan89crx
generally about 12% lower, so 280 x .88 = 246whp @ 17psi...
weird, i made 250whp on a 100% stock GSR with the same turbo @ 7psi, a log manifold on a pig rich tune
weird, i made 250whp on a 100% stock GSR with the same turbo @ 7psi, a log manifold on a pig rich tune
02-28-2007, 12:33 PM
#44
3.0 BAR
Join Date: Dec 2004
Posts: 1,976
Re: 406whp/281wht Stock Sleeve Turbo D16z6 Video/Dyno Sheet
Originally Posted by mtber
Hey dumbass, you did your math backwards... The dyno reads low, not high.
. even so, 313hp isnt anything amazing eitherbusiness ethics at its best. calling names on online forums. get a rope and hang yourself you cocksmuggler
oh, i hear your business does great work too. here is a customer review from another site
i would not recommend phearable.net. i ordered a p28 from them and got some other ecu converted to a vtec and auto-to manual. the ecu also causes the car to hicup and i dont know why. im trying to get a replacement but i dont think hes going to do anything. so i give thumbs down for phearble.
02-28-2007, 12:35 PM
#45
0.0 BAR
Thread Starter
Join Date: Jul 2003
Posts: 31
Re: 406whp/281wht Stock Sleeve Turbo D16z6 Video/Dyno Sheet
Originally Posted by ryan89crx
killer ------- attidute doucherocket . even so, 313hp isnt anything amazing either
business ethics at its best. calling names on online forums. get a rope and hang yourself you cocksmuggler
oh, i hear your business does great work too. here is a customer review from another site
. even so, 313hp isnt anything amazing eitherbusiness ethics at its best. calling names on online forums. get a rope and hang yourself you cocksmuggler
oh, i hear your business does great work too. here is a customer review from another site
i would not recommend phearable.net. i ordered a p28 from them and got some other ecu converted to a vtec and auto-to manual. the ecu also causes the car to hicup and i dont know why. im trying to get a replacement but i dont think hes going to do anything. so i give thumbs down for phearble.
shove it up your *** jerkoff
shove it up your *** jerkoff
Originally Posted by IowaTCoupe
134. 1.8L b18c1, built motor, stock sleeves, skunk2 intake manifold, 2.5 bar map sensor, 60/.63 t3/t04e turbo, inlinepro turbo manifold, 550cc injectors. Street tuned on crome pro at 17 psi on pump. Made 280 whp 229 wht.
Something VERY wrong here.... on 17 psi... w/ a b18c1 vtec engine.... your tune only made 280whp
?
AND... how do u know how much power if it was STREET tuned?!?!
My d16z6 made over 300hp w/ the same boost levels!!!!
Something VERY wrong here.... on 17 psi... w/ a b18c1 vtec engine.... your tune only made 280whp
?AND... how do u know how much power if it was STREET tuned?!?!
My d16z6 made over 300hp w/ the same boost levels!!!!
Thank you for pointing out the mistake on the website.
Concerning the ecu the customer had an issue with, all the customer needed to do was contact us & we would replace the ecu.
All you are going to continue to do is try and pull up the negatives you can find. Go ahead, I am sure there are some people that had a problem that we probably resolved for them. The ratio of problems to customer's that had no issues at all is around ten problems to around seven hundred plus customers.
02-28-2007, 12:42 PM
#46
0.0 BAR
Join Date: May 2005
Posts: 0
Re: 406whp/281wht Stock Sleeve Turbo D16z6 Video/Dyno Sheet
Damn. I need to raise my prices.
Phearable sells a basic no ***** and giggles chip kit for $35. I chip ecu's locally for just $10 more.
02-28-2007, 12:50 PM
#47
3.0 BAR
Join Date: Oct 2006
Posts: 2,330
Re: 406whp/281wht Stock Sleeve Turbo D16z6 Video/Dyno Sheet
Originally Posted by mtber
My mistake, 373 whp & 264 wht uncorrected on a dyno dynamics were his numbers. Should I have him fax over the dynosheet for you ?
Thank you for pointing out the mistake on the website.
Concerning the ecu the customer had an issue with, all the customer needed to do was contact us & we would replace the ecu.
Thank you for pointing out the mistake on the website.
Concerning the ecu the customer had an issue with, all the customer needed to do was contact us & we would replace the ecu.
You know, Ive never heard of pherable.net or whatever, but after reading your immature replies, I cant see how anyone would do business with you. If you really dont give a ---- about HMT, then why the hell did you post your dyno sheets here in the first place and why do you continue to try and defend yourself on a forum full of ppl who obivously hate you
BTW, your last reply was in your quote. :1
02-28-2007, 12:54 PM
#48
3.0 BAR
Join Date: Jul 2006
Posts: 2,349
Re: 406whp/281wht Stock Sleeve Turbo D16z6 Video/Dyno Sheet
Originally Posted by Joseph Davis
Insinuating that I am a liar will not get you far, anyone who has spent more than a few hours in my company can attest that I do not lie. That's a few people more than 130. 
It's not like I do this for money, and I don't ----- my accomplishments across the internet to aggrandize my ego. I'm some sort of freak nutjob who just genuinely likes cars - imagine that! What ulterior motive do I have to lie in this matter? Absolutely none. What reason do I have for criticising you publicly? Uh, I've stated them, but to make it perfectly clear since you are so perfectly dense: this is one of the handful of places I consider home, and you are not to prey upon it's denizens with your ching chong meow wares; go sell your less than impressive services to the Honda-Bling Farced Induction Forum kiddies, 97% of whom do not deserve to be breathing my air.
The sort of people you sell basemaps to generally lack knowledge, equipment, talent to deduce you're a crap artist. The ones with the ability to learn see what they've gotten from dealing with you, see how they can do a much better job themselves, and have no further use for you - they've gladly resolved their own issues.
It's not like I do this for money, and I don't ----- my accomplishments across the internet to aggrandize my ego. I'm some sort of freak nutjob who just genuinely likes cars - imagine that! What ulterior motive do I have to lie in this matter? Absolutely none. What reason do I have for criticising you publicly? Uh, I've stated them, but to make it perfectly clear since you are so perfectly dense: this is one of the handful of places I consider home, and you are not to prey upon it's denizens with your ching chong meow wares; go sell your less than impressive services to the Honda-Bling Farced Induction Forum kiddies, 97% of whom do not deserve to be breathing my air.
The sort of people you sell basemaps to generally lack knowledge, equipment, talent to deduce you're a crap artist. The ones with the ability to learn see what they've gotten from dealing with you, see how they can do a much better job themselves, and have no further use for you - they've gladly resolved their own issues.
02-28-2007, 12:56 PM
#49
0.0 BAR
Join Date: Dec 2003
Posts: 0
Re: 406whp/281wht Stock Sleeve Turbo D16z6 Video/Dyno Sheet
Kinda funny how xeno stepped out of the ring and said we shouldn't bash although he himself was bashed...
02-28-2007, 12:57 PM
#50
3.0 BAR
Join Date: Dec 2004
Posts: 1,976
Re: 406whp/281wht Stock Sleeve Turbo D16z6 Video/Dyno Sheet
Originally Posted by SinisterCRX
Kinda funny how xeno stepped out of the ring and said we shouldn't bash although he himself was bashed...
