question about my setup
#1
question about my setup
Ok, please understand that this is my first turbo setup and Still learning.
here is my setup-
t3 Turbo internal wastegate set at 8 PSI (I still have to figure out how to change the boost setting on internal wastegates) if anyone knows please inform me
hf manifold
adaptor plate
vafc
DSM 450cc injectors with resitor box
johnny race car 6inch intercooler
my questions are
1. How do I change the boost setting on an internal wastegate
2. Will my vafc be sufficent enogh to manage my fuel for my setup.
I've done some research and it seems to me like this will work since I'm running low boost.
I just want to make sure before I put all of this together and blow my motor
thanks for any help.
here is my setup-
t3 Turbo internal wastegate set at 8 PSI (I still have to figure out how to change the boost setting on internal wastegates) if anyone knows please inform me
hf manifold
adaptor plate
vafc
DSM 450cc injectors with resitor box
johnny race car 6inch intercooler
my questions are
1. How do I change the boost setting on an internal wastegate
2. Will my vafc be sufficent enogh to manage my fuel for my setup.
I've done some research and it seems to me like this will work since I'm running low boost.
I just want to make sure before I put all of this together and blow my motor
thanks for any help.
#2
Re:question about my setup
Originally Posted by 92lxsedan
1. How do I change the boost setting on an internal wastegate
Lengthen or shorten the actuator rod to lower or raise boost respectively.
2. Will my vafc be sufficent enogh to manage my fuel for my setup.
Engine Management FAQ Section 2, Question 5
Lengthen or shorten the actuator rod to lower or raise boost respectively.
2. Will my vafc be sufficent enogh to manage my fuel for my setup.
Engine Management FAQ Section 2, Question 5
#5
Re:question about my setup
I'd keep reading through the forums and the FAQ. But you'd want to lengthen the rod to lower boost, shorten it to raise boost.
And as far as something to adjust timing, yes... Alot of guy's here run the MSD BTM. It lets you retard ignition timing by the twist of a **** inside the vehichle. Even if you don't go with a BTM, you should still retard your timing somehow.
And as far as something to adjust timing, yes... Alot of guy's here run the MSD BTM. It lets you retard ignition timing by the twist of a **** inside the vehichle. Even if you don't go with a BTM, you should still retard your timing somehow.
#8
Re:question about my setup
hehe, I beleive what Ef9 is trying to tell you is. Stay away from the FMU. AT least stick with the AFC and 450's. The FMU is a mechanical unit that really only raises fuel pressure to your stock injectors. Most of them have close to no tuneability, and if there was ever a mechanical failure due to either the FMU , your fuel pump dying out, or a maxed out injector... say good by to your nice turbo engine
#9
Re:question about my setup
and yes, you'd still need to retard timing! Correct me if i'm wrong, but with any turbo setup, it's a good idea to retard your timing because with the forced induction of a turbo, the intake charge is more dense. If you don't retard your timing, while the engine is under boost you can get pre- ignition (detonation) which in time will destroy your engine. Theres many things that we use to try to minimize pre-ignition and intake temp' etc. i.e: colder spark plugs, intercoolers, timing retardation, high octaine fuel, lower compression, good tuning etc.
Thread
Thread Starter
Forum
Replies
Last Post
typer
Forced Induction
8
08-18-2004 05:31 PM
ACCHYBRID
Turbo Parts For Sale
4
08-09-2004 10:14 AM