Motorola (Freescale) 2.5 BAR and 4 BAR map sensor mods (56k....thumbnails) - HomemadeTurbo - DIY Turbo Forum

Go Back  HomemadeTurbo - DIY Turbo Forum > Homemadeturbo > Engine Management
Motorola (Freescale) 2.5 BAR and 4 BAR map sensor mods (56k....thumbnails) >

Motorola (Freescale) 2.5 BAR and 4 BAR map sensor mods (56k....thumbnails)

Engine Management eCtune , Crome , AFC , FMU , Zdyne , Hondata , EMS , TE , Uberdata Anything to control your fuel, spark needs!

Motorola (Freescale) 2.5 BAR and 4 BAR map sensor mods (56k....thumbnails)

Old 01-19-2007, 12:00 PM
  #1  
0.0 BAR
Thread Starter
 
Join Date: May 2005
Posts: 0
Default Motorola (Freescale) 2.5 BAR and 4 BAR map sensor mods (56k....thumbnails)

Here are two mods for the commonly used Freescale 2.5 BAR MAP sensor and a newer 4 BAR MAP sensor.


First the 2.5 BAR.

An adpater made from 1/2" aluminum and a 90 degree 1/8 NPT to barb fitting was used so the source could be taken where the old MAP sensor was.




This one is one that wasn't finished. JB-WELD action .




A firewall mounted honda MAP sensor donated its housing so that the stock harness would not have to tapped into or modified.




2.5 BAR soldered, installed, and plastic epoxy was used to seal and secure the 2.5 BAR to the stock housing housing.




Installed and painted black for HMT stealthness.







Now to the 4 BAR.

Here it is. Just a WARNING to you all. The pin arrangement on this sensor is listed incorrectly everywhere on Freescale's website and PDF file. They list as SSOP, BUT it is not. The pin spacing is 0.050". SSOP uses a 0.025" spacing, so this is actually SOIC WIDE spacing. Only problem is that 8 pin SOIC WIDE is not a common pin arrangement. 8 pin SOIC NARROW is, but it won't line up at all. You could order a 16 pin SOIC WIDE adapter, but you would need to solder the sensor in the middle pins 3-6 and 11-15 and break off the ends since it won't fit in the stock MAP sensor housing.




Stock MAP hollowed out and the sensor soldered.




All finished. The same plastic epxoy was used to fill in and seal the cover, since you would've had to cut the rivets that normally hold the cover down. Comparison of the size of the sensor.




Pinout for small MAP sensors






Here are the part #'s for the SOIC sensors. You can get these sensors from any Freescale distributor.

The two part numbers are the same sensor, it's just how they package them. "T1" is for Tape and Reels and "U" is for Rails.

7 BAR
MPXH6700AC6U
MPXH6700AC6T1

4 BAR
MPXH6400AC6U
MPXH6400AC6T1

3 BAR
MPXH6300AC6U
MPXH6300AC6T1




0b00st0 is offline  
Old 01-19-2007, 12:04 PM
  #2  
3.0 BAR
 
Join Date: Dec 2004
Posts: 1,976
Default Re: 2.5 BAR and 3 BAR MAP Sensor Mods (56k....thumbnails)

hell yes, nice!
ryan89crx is offline  
Old 01-19-2007, 01:05 PM
  #3  
0.0 BAR
 
Join Date: Jun 2005
Location: WA
Posts: 0
Default Re: 2.5 BAR and 3 BAR MAP Sensor Mods (56k....thumbnails)

good ----.

maybe this should be put in the tech write ups?
Oscar is offline  
Old 01-19-2007, 01:12 PM
  #4  
3.0 BAR
 
Join Date: Jun 2003
Posts: 3,975
Default Re: 2.5 BAR and 3 BAR MAP Sensor Mods (56k....thumbnails)

Originally Posted by MADMAX
Installed and painted black for HMT stealthness.
That's a pic installed on my car now. The white epoxy was also painted black.
The wiring harness is long enough to mount it on the firewall using a longer hose of course. I might do that and use some black hex screws so they are less noticeable.

Thanks again Madmax. Now for a re-tune and more boost.
whiterice is offline  
Old 01-19-2007, 01:40 PM
  #5  
0.0 BAR
Thread Starter
 
Join Date: May 2005
Posts: 0
Default Re: 2.5 BAR and 3 BAR MAP Sensor Mods (56k....thumbnails)

Originally Posted by whiterice
Thanks again Madmax. Now for a re-tune and more boost.

15-17 psi You up for a little time on the dyno after the street tuning?


I'm curious on how this S trim wheel will perform.


0b00st0 is offline  
Old 01-19-2007, 01:57 PM
  #7  
3.0 BAR
 
Join Date: Jun 2003
Posts: 3,975
Default Re: 2.5 BAR and 3 BAR MAP Sensor Mods (56k....thumbnails)

Originally Posted by MADMAX
15-17 psi You up for a little time on the dyno after the street tuning?
yes and yes
whiterice is offline  
Old 01-19-2007, 01:58 PM
  #8  
3.0 BAR
 
Join Date: Jan 2003
Posts: 4,403
Default Re: 2.5 BAR and 3 BAR MAP Sensor Mods (56k....thumbnails)

for this, Darth must personally say...

RENR is offline  
Old 01-19-2007, 02:16 PM
  #9  
0.5 BAR
 
Join Date: Jun 2006
Posts: 109
Default Re: 2.5 BAR and 3 BAR MAP Sensor Mods (56k....thumbnails)

nicee.
if we install that 3bar then what values are we suppose to use in crome?
moak89 is offline  
Old 01-19-2007, 02:19 PM
  #10  
0.5 BAR
 
Join Date: Jun 2006
Posts: 109
Default Re: 2.5 BAR and 3 BAR MAP Sensor Mods (56k....thumbnails)

wow i just checked the freescale website and they've listed that sensor for 58 psi. so that means its good for upto 44psi . good goin
moak89 is offline  

Thread Tools
Search this Thread
Quick Reply: Motorola (Freescale) 2.5 BAR and 4 BAR map sensor mods (56k....thumbnails)


Contact Us Sitemap Advertising Cookie Policy Privacy Statement Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.