Crome wont "put" to Ostrich
#1
Crome wont "put" to Ostrich
Having problems putting the bin into the ostrich. ECU is P28 auto i converted it buy cutting RP17 and jumping RP18 runs car fine if i have J1 unhooked (doesn't throw any codes). I also cut J12 for use of my Hulog. and i am runing crome 1.5 (free edition of coarse).
1. connect ostrich to lap top open device manager and look at port and baud settings. ( have tried alot of different ports and baud rates)
2. open crome then load a p28 or p30 rom.
3. remove checksum
4. settings - real time programing - Moates Ostrich/Burn 1 set com port and baud rate ( 4 some reason it will change to 115200 or 920000 after clicking detect connection and it will say connected).
5. save changes made then click real time toolbar button. then press "Put" I get
""Timed Out the operation failed after 128 attempt(s) with 10 milliseconds each attempt.
I have no clue why i cannot connect anymore i even searched on here and found another thread about using Tuner Pro RT i downloaded it but i cant work it for crap? any help guys please!
1. connect ostrich to lap top open device manager and look at port and baud settings. ( have tried alot of different ports and baud rates)
2. open crome then load a p28 or p30 rom.
3. remove checksum
4. settings - real time programing - Moates Ostrich/Burn 1 set com port and baud rate ( 4 some reason it will change to 115200 or 920000 after clicking detect connection and it will say connected).
5. save changes made then click real time toolbar button. then press "Put" I get
""Timed Out the operation failed after 128 attempt(s) with 10 milliseconds each attempt.
I have no clue why i cannot connect anymore i even searched on here and found another thread about using Tuner Pro RT i downloaded it but i cant work it for crap? any help guys please!
#4
Re: Crome wont "put" to Ostrich
i have the first ostrich i think the ostrich 2.0 was made for 920000. ill try again ill set it at 9600 or 34800 and it will change to 115000 or some ---- like that and ill go and change the setting to 115000 also and nothing or leave it at 9600 then it will change and still same nothing. it detects a connection but just wont put it to the ostrich.
#6
Re: Crome wont "put" to Ostrich
found this
http://www.moates.net/documentation....entation_id=22
the only thing for a firmware update is for 2.0 should i update to that software?
http://www.moates.net/documentation....entation_id=22
the only thing for a firmware update is for 2.0 should i update to that software?
#7
Re: Crome wont "put" to Ostrich
Originally Posted by Ef8sirjunkie
found this
http://www.moates.net/documentation....entation_id=22
the only thing for a firmware update is for 2.0 should i update to that software?
http://www.moates.net/documentation....entation_id=22
the only thing for a firmware update is for 2.0 should i update to that software?
#9
Re: Crome wont "put" to Ostrich
Originally Posted by lilpooh21186
make sure your baud rate is the highest like 9200000 or some ---- like that
That works for Ostrich v2.0, ***** you for Ostrich v1.0
Originally Posted by stenseltizm
11500 sounds familiar
Thread
Thread Starter
Forum
Replies
Last Post
TomBones
Engine Management
30
03-01-2009 05:30 PM
cloud
Engine Management
49
12-05-2007 02:41 PM
W O T
General Discussion
23
12-10-2005 05:16 PM