Burn one problem again
Thread Starter
1.0 BAR
Joined: Sep 2006
Posts: 221
Burn one problem again
For the life of i cannot get a .bin file to burn right.It runs good in boost on a stock ecu, but not a chipped one.
No i'm not flooring with a stock ecu.Every .bin i burn cuts out in boost.It's like it hits a fuel cut.
I'm running a very small *** volvo turbo,obd2 to obd 1 harness,chipped p28,240cc injectors,NGK-11 cold *** plug.
I have some 460 injectors, i'll put in tomorrow. I don't think that's going to help me if, i can't burn the rom right.All
my setting on the burner is correct.I can burn a stock rom and it runs fine. It cuts out at 5000 or when it see 4-5 psi of boost.
Every freaking bin i burn.
If i change any of the setting's in uber on a rom, i have too import a p28 correct?
No i'm not flooring with a stock ecu.Every .bin i burn cuts out in boost.It's like it hits a fuel cut.
I'm running a very small *** volvo turbo,obd2 to obd 1 harness,chipped p28,240cc injectors,NGK-11 cold *** plug.
I have some 460 injectors, i'll put in tomorrow. I don't think that's going to help me if, i can't burn the rom right.All
my setting on the burner is correct.I can burn a stock rom and it runs fine. It cuts out at 5000 or when it see 4-5 psi of boost.
Every freaking bin i burn.
If i change any of the setting's in uber on a rom, i have too import a p28 correct?
0.0 BAR
Joined: Oct 2005
Posts: 0
Re: Burn one problem again
wow, get your setup complete before you do anything else.
1st question, why the hell are you still using Uberdata? It is pretty much an abandoned project. Crome has tons of features and is still in constant development.
I haven't used UD in a long *** time, but you will first start out with the stock GSR bin. Tehn you import whatever is closest to whatever engine you are running. Assuming you are running a D16Y8, then you need to import a P28 map.
The Burn1 itself is pretty damn idiot proof. I think you are most likely running into a problem of not knowing how to set up your ROM. Read the FAQs some more if need be.
1st question, why the hell are you still using Uberdata? It is pretty much an abandoned project. Crome has tons of features and is still in constant development.
I haven't used UD in a long *** time, but you will first start out with the stock GSR bin. Tehn you import whatever is closest to whatever engine you are running. Assuming you are running a D16Y8, then you need to import a P28 map.
The Burn1 itself is pretty damn idiot proof. I think you are most likely running into a problem of not knowing how to set up your ROM. Read the FAQs some more if need be.
crome
Thread Starter
1.0 BAR
Joined: Sep 2006
Posts: 221
Re: Burn one problem again
I'll try to use crome.I only had one map 2 years ago that worked.bbka 1.66 240cc tune..All the other ones don't work.Atleast not for me.
Yeah its a pos d16y8.I need to go back with a d15z1 vx block.Its the only one i had luck with.
Yeah its a pos d16y8.I need to go back with a d15z1 vx block.Its the only one i had luck with.
Thread Starter
1.0 BAR
Joined: Sep 2006
Posts: 221
Re: Burn one problem again
Originally Posted by ghettoturbo
....your problem is that youre trying to run 240s imho. Put in the bigger injectors and make a basemap for them.
Did it with crome, runs like a champ..Except part throttle.I put the 460's in.
3.0 BAR
Joined: Mar 2003
Posts: 21,468
Re: Burn one problem again
Originally Posted by snm95ls
The Burn1 itself is pretty damn idiot proof.
I'm a retard when it comes to computers so that might have something to do with it though. :1
Originally Posted by ghettoturbo
....your problem is that youre trying to run 240s imho. Put in the bigger injectors and make a basemap for them.
That's where I'm putting my money.
__________________
Best Car Insurance | Auto Protection Today | FREE Trade-In Quote
Thread
Thread Starter
Forum
Replies
Last Post
