Best way to datalog (uberdata)
03-30-2005, 07:00 AM
#22
3.0 BAR
Join Date: May 2004
Posts: 5,042
Re: Best way to datalog (uberdata)
Originally Posted by xenocron
If you have a female end to put on the end of the USB cable, you should be able to plug it into that little white male port
03-30-2005, 07:39 AM
#23
1.0 BAR
Join Date: Jan 2005
Posts: 425
Re: Best way to datalog (uberdata)
I have been using the same 4 pin female connector that comes with the RTP kits and also the some of the other datalogging kits. you just solder the corresponding wires to the correct pins. Slip them in the connector and then plug it in. But to tell you the truth, datalogging using ebay USB cables has become such a pain in the *** lately, that I have given up. I have used many cables, and the one stated above with the blue,yellow and white will work. Just put the blue wire where the green one was on the other cable and you are set. So it should be blue -> pin 1 , yellow pin->2 and white -> pin 4.
I just got a bad batch of cables, I serisously don't understand. I will get 5 cables in and 3 will work two will not. Using the exact same cables, even using the same ecu in some cases. Even tried soldering to the board and also soldering a connector. Still nothing. So I give up and I am going serial. It is much easier and less of a hassle to get working in my opinion. The superdroid cable will plug right in. you need to swtich the +5 and the Rx I believe. But you will see when you get it, the cables are marked.
I just got a bad batch of cables, I serisously don't understand. I will get 5 cables in and 3 will work two will not. Using the exact same cables, even using the same ecu in some cases. Even tried soldering to the board and also soldering a connector. Still nothing. So I give up and I am going serial. It is much easier and less of a hassle to get working in my opinion. The superdroid cable will plug right in. you need to swtich the +5 and the Rx I believe. But you will see when you get it, the cables are marked.
03-30-2005, 07:48 AM
#24
3.0 BAR
Join Date: Apr 2003
Posts: 11,058
Re: Best way to datalog (uberdata)
i hate usb cables, they're a pita. serial cables are so fresh and so clean clean.
[img width=600 height=550]http://www.draglab.com/hmt/projektegdizzle/datalogging.jpg[/img]
[img width=600 height=550]http://www.draglab.com/hmt/projektegdizzle/datalogging2.jpg[/img]
not to mention, you don't have to search the net to find the right drivers, pin outs for your particular cable, etc. and no switching of any wires with this particular cable either, it plugs right up.
[img width=600 height=550]http://www.draglab.com/hmt/projektegdizzle/datalogging.jpg[/img]
[img width=600 height=550]http://www.draglab.com/hmt/projektegdizzle/datalogging2.jpg[/img]
not to mention, you don't have to search the net to find the right drivers, pin outs for your particular cable, etc. and no switching of any wires with this particular cable either, it plugs right up.
03-30-2005, 09:11 AM
#25
1.0 BAR
Join Date: Jan 2005
Posts: 425
Re: Best way to datalog (uberdata)
Originally Posted by projekteg
i hate usb cables, they're a pita. serial cables are so fresh and so clean clean.
not to mention, you don't have to search the net to find the right drivers, pin outs for your particular cable, etc. and no switching of any wires with this particular cable either, it plugs right up.
not to mention, you don't have to search the net to find the right drivers, pin outs for your particular cable, etc. and no switching of any wires with this particular cable either, it plugs right up.
I should have gotten the longer one.
Thread
Thread Starter
Forum
Replies
Last Post
FooK
Engine Management
22
04-17-2005 08:34 PM
ComputerJLT
Engine Management
13
03-06-2004 07:17 PM
