vtec head on a zc?
#11
Re:vtec head on a zc?
I don't think they will bolt up for some reason.
__________________
Best Car Insurance | Auto Protection Today | FREE Trade-In Quote
__________________
Best Car Insurance | Auto Protection Today | FREE Trade-In Quote
#14
Re:vtec head on a zc?
the valve relief in the pistons
DOHC piston have valve relief for DOHC head
AND SOHC pistons have valve relief for SOHC head
i guess if u where to use differennt piston but i am not sure about the bolting up part
DOHC piston have valve relief for DOHC head
AND SOHC pistons have valve relief for SOHC head
i guess if u where to use differennt piston but i am not sure about the bolting up part
#15
Re:vtec head on a zc?
Actually the valve releifs are about the same size and that really isnt the problem. Oil passages are not shaped the same, and some chanfering needs to be done. 2 head bolts do NOT align up, and some serious drilling would be needed to be done on the head, and I have no idea if their is enough meat in the ZC head to cut away to be safe and have the bolt still go through?? I mocked one up and looked at everything, The cylinders all align just fine with the head. ITs real real close, but the head bolt situation makes it a big NO GO!
Also if you were to put a DOHC ZC head on say a D16a6 you would get around 8.25 c/r. Which is really low for a honda and probably would run like ----.
Also if you were to put a DOHC ZC head on say a D16a6 you would get around 8.25 c/r. Which is really low for a honda and probably would run like ----.
#17
Re:vtec head on a zc?
Some one on this board was saying how you can put a DOHC ZC on a d block. ive never ehard of that before but i guess anythings possible right??$$
i recently put a z6 on a SOHC ZC, does anyone know if the SOHC ZC have the pm7(jdm zc) pistons?
while doing the swap i was too busy scraping the head gasket off the block i forgot to look...!
if it IS the pm7 pistons my set-up yeilds 12.35.
if my ZC came with the pm6 pistons set up yeilds 9.71.
both are with the .048 thickness gasket in an attempt to lower compression for boost.
* according to http://www.knology.net/~jediklc/D.htm *
i kick myself in the *** for forgetting to look at the pistons...
post some ideas up about worst case scenario, 12.35 comp. with boost, yikes...!
i recently put a z6 on a SOHC ZC, does anyone know if the SOHC ZC have the pm7(jdm zc) pistons?
while doing the swap i was too busy scraping the head gasket off the block i forgot to look...!
if it IS the pm7 pistons my set-up yeilds 12.35.
if my ZC came with the pm6 pistons set up yeilds 9.71.
both are with the .048 thickness gasket in an attempt to lower compression for boost.
* according to http://www.knology.net/~jediklc/D.htm *
i kick myself in the *** for forgetting to look at the pistons...
post some ideas up about worst case scenario, 12.35 comp. with boost, yikes...!
#19
Re:vtec head on a zc?
ShoPow,
i put a Z6 head on a SOHC ZC shortblock...
I'n not quiet sure i understand your Q.
but if your asking if the SOHC ZC IM will fit other d-series blocks?
A: yes, it will fit but my ZC came carburated, and yes i used the Z6 IM with the z6 head.
i put a Z6 head on a SOHC ZC shortblock...
I'n not quiet sure i understand your Q.
but if your asking if the SOHC ZC IM will fit other d-series blocks?
A: yes, it will fit but my ZC came carburated, and yes i used the Z6 IM with the z6 head.