"oh shit"...wtf did i do...
 

my car has been runin shitty and sort of slow and not quite as strong as it used to after i built it and put new pistons and rings in it valve seals and ---- like that...i just pulled off my stock 4-2-1 header ...so i can put my turbo mani on and...my second from the right exaust port has wet oil and has like almost no carbon build up.....but all my other 3 ports are dry and have nice clean caron build up ....im tryin to figure out whats goin on...like am i leaking oil thru the rings or some ----....i dont know but this ------ car is my worst enemy

Re: "oh shit"...wtf did i do...
 

Tune? Low compression pistons would be the reason your car is shitty when its not under boost.

Re: "oh shit"...wtf did i do...
 

Possibly valve seals? How many miles on the motor and have you ever replaced the valve seals before.

Re: "oh shit"...wtf did i do...
 

um i looked into my port more closely and one side is clean and the other side has some wet carbon....i also looked at my plug (cheapest plugs i could buy)...and the plug has the same wet carbon and fuel ---- on it ...so im thinkin my ---- wasent fireing that well in that cylinder...and my valve seals and rings are brand new...so i think im gettin weak spark and so im goin to try and get some really good plugs.. and check my spark...i also noticed when my car idled ...it would miss fire every couple of rotations

Re: "oh shit"...wtf did i do...
 

Well does the mystery substance have the consistency of oil or gas?

Low RPM ignition misses can also be caused by serious engine damage.

Re: "oh shit"...wtf did i do...
 

honestly a little bit of both... usually when u get some of that ---- on ur finger if its carbon it will dry up pretty quick...but when i touch this ---- it feels like the carbon but it dosent dry up.....im wondering if i fouled out the plug a long time ago and maybe the rings in that cylinder havent seeted yet and maybe its letting some oil passed them....i havent really drove the car that much since the build......and when i do drive it and it feels slugish...it feels like its geting weak spark...and in the high rpms it dosent sound smooth....so im wondering if maybe im just carrying around that extra cylinder thats not fireing...wihich would explain my lose in power...my miss fire ...my plug being all shity...and my port looking the same as my plug..

Re: "oh shit"...wtf did i do...
 

was there any oil on that plug? or in the spakplug tube? i would just put some NGK plugs in it along with a standard tune up if you havent already and go from there. id also do a compression test and check your timing. did you hook up a timing light to the motor when you put it back together

Re: "oh shit"...wtf did i do...
 

Back when I did my clutch on my integra I noticed two exhaust ports where 100% clean, the other two normal carbon covered. A month later, the headgasket blew for the two ports that were clean. They were being steam-cleaned from the leaking coolant. Sounds like it could be your issue, but who knows. I remember before you were having headgasket issues...is this the same motors?

My car also did not run 100% when the HG was leaking a little. Once it was replaced, it ran better than ever. This could be it. You might want to try to pump some air into each cylinder while you have each at tdc to see if you get any bubbles in the coolant at all.

Re: "oh shit"...wtf did i do...
 

yah i am the one who had the head gasket problem.. i got a new one and some arp headstuds... and it seemed to seal up fine after that but i will check it..still i never thought of the blowing air into the cylinder...thanks

Re: "oh shit"...wtf did i do...
 

yah there was oil on the plug and my timing is right on...i am going to put some iridiums in there...because those are the best n cleanest plugs ive ever used