help with building a d16a6 for boost
06-19-2003, 10:03 PM
#1
0.0 BAR
Thread Starter
Join Date: Jun 2003
Posts: 9
help with building a d16a6 for boost
I'm getting a d16a6, and a zc dohc 1.6 also from a friend of mine. He spun a main bearing in the zc after he pulled the d16a6 from his crx si. He said that the stock si motor ran fine when he pulled it out and apart, but since its out i should go ahead and get the crank resurfaced, and get new main bearings. Also to take the zc pistons and rods out and put them in the d16a6 since they have a little bit higher compression. I was wondering if i had to get new rod bearings when i get the crank resurfaced, and if i should put new rings in it also? I was also wondering if this would be a half way decent set up running all stock minus the pistons and rods from that zc at around 6 lbs. of boost with out an intercooler? If anyone can help i would appreciate it.....
06-19-2003, 10:10 PM
#2
3.0 BAR
Join Date: Mar 2003
Posts: 21,479
Re:help with building a d16a6 for boost
Your going to bump the compression up and run boost? Check this site out. http://www.knology.net/~jediklc/D.htm
That would put your compression at 10.775:1
If you are going to rebuild it you should use new parts instead of swapping rings and ---- from the raped ZC.
__________________
Best Car Insurance | Auto Protection Today | FREE Trade-In Quote
That would put your compression at 10.775:1
If you are going to rebuild it you should use new parts instead of swapping rings and ---- from the raped ZC.
__________________
Best Car Insurance | Auto Protection Today | FREE Trade-In Quote
06-19-2003, 11:04 PM
#3
0.0 BAR
Thread Starter
Join Date: Jun 2003
Posts: 9
Re:help with building a d16a6 for boost
check out this rebuild kit that i found on ebay though. This is what i was just thinkin of doin. That way i will have a fresh motor to boost. http://cgi.ebay.com/ebaymotors/ws/eB...ory=46098&rd=1
06-19-2003, 11:14 PM
#4
3.0 BAR
Join Date: Mar 2003
Posts: 21,479
Re:help with building a d16a6 for boost
Looks good. That should be just fine for 6 psi. You would be better off with that than swapping used ZC parts into it. You could always keep the ZC for a project or sell it.
__________________
Best Car Insurance | Auto Protection Today | FREE Trade-In Quote
__________________
Best Car Insurance | Auto Protection Today | FREE Trade-In Quote
06-19-2003, 11:17 PM
#5
0.0 BAR
Thread Starter
Join Date: Jun 2003
Posts: 9
Re:help with building a d16a6 for boost
ya how much do u think i could get for a zc block with a new oil and water pump on it. It doesnt have a head on it, but has a resurfaced flywheel. Im only payin fifty bucks for the si and zc motor. Think i can at least make my money back
06-19-2003, 11:22 PM
#6
3.0 BAR
Join Date: Mar 2003
Posts: 21,479
Re:help with building a d16a6 for boost
Put it in the classified section for $50 and I'm sure someone would jump on it. Depending on where you live since shipping would be pricey if it was too far away.
__________________
Best Car Insurance | Auto Protection Today | FREE Trade-In Quote
__________________
Best Car Insurance | Auto Protection Today | FREE Trade-In Quote
Thread
Thread Starter
Forum
Replies
Last Post
