Got fuel, spark, compression, timing, and grounds, but the car still won't start
#21
Re: Got fuel, spark, compression, timing, and grounds, but the car still won't s
Originally Posted by chris
worn clutch cable yo
buy a factory honda unit dont buy a vatozone one unless you like replcacing he pedal assembley
also did you replace throwout bearing when you changed the clutch
buy a factory honda unit dont buy a vatozone one unless you like replcacing he pedal assembley
also did you replace throwout bearing when you changed the clutch
Yes, I replaced all the bearings + had the flywheel machined, all at the same shop.
I'm friends with a guy who works there so regardless it's going back for them to look at and double check. If it ***** off again after I put it in, I'll spring for a new OEM clutch cable. Any other tips for super stiff clutches?
#22
Re: Got fuel, spark, compression, timing, and grounds, but the car still won't s
oem clutch cables
I also had to use a spacer on the clutch cable bracket when I switched to an act extreme plate
car wouldnt hit gears right
2 other cars I know personally had the same issue
welded around an inch of pipe and slight the pipe to fit the cable in. Worked like a charm. Im rebuilding the car right now sohc vtec all motor junk
I also had to use a spacer on the clutch cable bracket when I switched to an act extreme plate
car wouldnt hit gears right
2 other cars I know personally had the same issue
welded around an inch of pipe and slight the pipe to fit the cable in. Worked like a charm. Im rebuilding the car right now sohc vtec all motor junk
#23
Re: Got fuel, spark, compression, timing, and grounds, but the car still won't s
Originally Posted by chris
oem clutch cables
I also had to use a spacer on the clutch cable bracket when I switched to an act extreme plate
car wouldnt hit gears right
2 other cars I know personally had the same issue
welded around an inch of pipe and slight the pipe to fit the cable in. Worked like a charm. Im rebuilding the car right now sohc vtec all motor junk
I also had to use a spacer on the clutch cable bracket when I switched to an act extreme plate
car wouldnt hit gears right
2 other cars I know personally had the same issue
welded around an inch of pipe and slight the pipe to fit the cable in. Worked like a charm. Im rebuilding the car right now sohc vtec all motor junk
Car on jacks, can't get it all the way into gear but 1/2 way engaged spins the tires.
#25
Re: Got fuel, spark, compression, timing, and grounds, but the car still won't s
Originally Posted by chris
try the spacer dude it might fix your problem
2 bucks of pipe and 10 minutes of your time. Bust out the flux core for hmt old school effect
2 bucks of pipe and 10 minutes of your time. Bust out the flux core for hmt old school effect
I would flux it just for the effect but it's too much of a pain to convert the MIG back over. I'll just set the wirespeed a little higher so it's nice and globby.
#26
Re: Got fuel, spark, compression, timing, and grounds, but the car still won't s
Originally Posted by Minor Threat
---- ya. I even have the pipe laying around from making traction bars.
I would flux it just for the effect but it's too much of a pain to convert the MIG back over. I'll just set the wirespeed a little higher so it's nice and globby.
I would flux it just for the effect but it's too much of a pain to convert the MIG back over. I'll just set the wirespeed a little higher so it's nice and globby.
that works
update this is a good thread with good trouble shooting stuff etc
#27
Re: Got fuel, spark, compression, timing, and grounds, but the car still won't s
Originally Posted by chris
that works
update this is a good thread with good trouble shooting stuff etc
Thread
Thread Starter
Forum
Replies
Last Post
alpalwal
Hybrid/Tech
13
01-07-2007 02:54 PM
davcivic
Hybrid/Tech
15
05-11-2004 01:32 PM
GUIL
Hybrid/Tech
9
10-23-2003 07:59 PM