D16Z6 Swap Wiring Q
#1
D16Z6 Swap Wiring Q
I have a 91 Civic SE (same as the DX DPFI) and I have a D16Z6 that I will probably be dropping into it. I know there are a few different ways to to the wiring, but which is easiest? Any benefits to one or the other?
Can I use my current ECU and Distributor and swap to MPFI and use an RPM activated switch for VTEC? Will the 5G intake manifold, injectors ect work if I keep the 4G distibutor and ECU?
Thanks for any suggestions or ideas
Can I use my current ECU and Distributor and swap to MPFI and use an RPM activated switch for VTEC? Will the 5G intake manifold, injectors ect work if I keep the 4G distibutor and ECU?
Thanks for any suggestions or ideas
#5
Re:D16Z6 Swap Wiring Q
Oh and when you get the the part about the injector resistor box. Disregarde it if you are going to use the ex ecu and dizzy. Just hook up the yellow/black wires coming off the injectors to the two yellow/black wires that went to the old dx injectos. They go back to the ecu. The reason I say this is that I thought they were a ground and they aren't. They have to go back to the ecu because if you ground them on the body they short out the #14 fuse and its a pain in the ***.
#6
Re:D16Z6 Swap Wiring Q
dpfi-->mpfi wiring:
c1 (orange)-->b10
c2 (white)-->b12
blue/green from dizzy-->c1
blue/yellow from dizzy-->c2
brown wire from injector 1-->a1
red wire from injector 2-->hook up to red dpfi injector wire
blue wire from injector 3--> a5
yellow wire from injector 4--> hook up to yellow dpfi injector wire
(I might have switched the locations of the red and yellow wires since I'm saying this from memory, if so then take note of that.)
c1 (orange)-->b10
c2 (white)-->b12
blue/green from dizzy-->c1
blue/yellow from dizzy-->c2
brown wire from injector 1-->a1
red wire from injector 2-->hook up to red dpfi injector wire
blue wire from injector 3--> a5
yellow wire from injector 4--> hook up to yellow dpfi injector wire
(I might have switched the locations of the red and yellow wires since I'm saying this from memory, if so then take note of that.)
#7
Re:D16Z6 Swap Wiring Q
to answer your questions...
1..do the dpfi to mpfi first.
2..YES you can use you current ecu if you LEAVE the dpfi on. but if you use mpfi, then NO
3..Yes, you can use teh 5 gen mani...sensors are jsut diff. colors and some stuff are switched around. everything fits though. you can use the 5 gen injectors too but they run without a resistor. you can add a resistor to them...but it wont do much. but if you KEEP the 4g ecu...no...none of these will work. you have to keep dpfi ecu for dpfi...and mpfi ecu for mpfi. good luck.
1..do the dpfi to mpfi first.
2..YES you can use you current ecu if you LEAVE the dpfi on. but if you use mpfi, then NO
3..Yes, you can use teh 5 gen mani...sensors are jsut diff. colors and some stuff are switched around. everything fits though. you can use the 5 gen injectors too but they run without a resistor. you can add a resistor to them...but it wont do much. but if you KEEP the 4g ecu...no...none of these will work. you have to keep dpfi ecu for dpfi...and mpfi ecu for mpfi. good luck.
Thread
Thread Starter
Forum
Replies
Last Post
NBLKID
Turbo Parts For Sale
6
09-24-2007 03:18 AM
mycrx
Hybrid/Tech
0
07-15-2006 07:43 PM
omahaturbocivic
Turbo Parts For Sale
1
02-17-2003 11:07 AM