Turbo install prep began tonite, BLAH
#1
Turbo install prep began tonite, BLAH
After talkin to steve-o last nite, I decied to get started on the turbo project, basically the prep for saturday. After takin shot off, I was very unhappy...
Took off the CAI and dist cap and wires...lots o room now.
[img width=640 height=480]http://www.we-todd-did-racing.com/wetoddimage.wtdr/wODU4NDEzNnM0MTNkZmQzMXk1NDE%3D.jpg[/img]
Oh yes, lovley GASH in my CAI, hhhmmm maybe that could be one of the MANY reasons my car was runnin shitty.
[img width=640 height=480]http://www.we-todd-did-racing.com/wetoddimage.wtdr/wODU4NDA3NnM0MTNkZmQzMXk1NDE%3D.jpg[/img]
The gash was cause by this little ******...im going to put something around it this time when I install the charge piping.
[img width=640 height=480]http://www.we-todd-did-racing.com/wetoddimage.wtdr/wODU4NDA4NnM0MTNkZmQzMXk1NDE%3D.jpg[/img]
I made a thread a while back about possible hydrolock, which would seem about right now, but no... The seals on the ren of the plug wires was broken, and it was letting in water to the dist cap, cuasing a short, and a misfire in one of my cylinders...*******!
[img width=640 height=480]http://www.we-todd-did-racing.com/wetoddimage.wtdr/wODU4NDA5NnM0MTNkZmQzMXk1NDE%3D.jpg[/img]
So, now I gotta drive down to Summit Racing to get new ones, but I never mind goin to Summit , got these bad boys...and a new dist cap.
[img width=640 height=480]http://www.we-todd-did-racing.com/wetoddimage.wtdr/wODU4NDEwNnM0MTNkZmQzMXk1NDE%3D.jpg[/img]
Well its a bit tight in there, so gotta take out the AC this week. Steve hook me up with them directions you told me yesterday.
[img width=640 height=480]http://www.we-todd-did-racing.com/wetoddimage.wtdr/wODU4NDExNnM0MTNkZmQzMXk1NDE%3D.jpg[/img]
I was ------ around with this ----, gettin stuff ready for saturday!
[img width=640 height=480]http://www.we-todd-did-racing.com/wetoddimage.wtdr/wODU4NDEyNnM0MTNkZmQzMXk1NDE%3D.jpg[/img]
Took off the CAI and dist cap and wires...lots o room now.
[img width=640 height=480]http://www.we-todd-did-racing.com/wetoddimage.wtdr/wODU4NDEzNnM0MTNkZmQzMXk1NDE%3D.jpg[/img]
Oh yes, lovley GASH in my CAI, hhhmmm maybe that could be one of the MANY reasons my car was runnin shitty.
[img width=640 height=480]http://www.we-todd-did-racing.com/wetoddimage.wtdr/wODU4NDA3NnM0MTNkZmQzMXk1NDE%3D.jpg[/img]
The gash was cause by this little ******...im going to put something around it this time when I install the charge piping.
[img width=640 height=480]http://www.we-todd-did-racing.com/wetoddimage.wtdr/wODU4NDA4NnM0MTNkZmQzMXk1NDE%3D.jpg[/img]
I made a thread a while back about possible hydrolock, which would seem about right now, but no... The seals on the ren of the plug wires was broken, and it was letting in water to the dist cap, cuasing a short, and a misfire in one of my cylinders...*******!
[img width=640 height=480]http://www.we-todd-did-racing.com/wetoddimage.wtdr/wODU4NDA5NnM0MTNkZmQzMXk1NDE%3D.jpg[/img]
So, now I gotta drive down to Summit Racing to get new ones, but I never mind goin to Summit , got these bad boys...and a new dist cap.
[img width=640 height=480]http://www.we-todd-did-racing.com/wetoddimage.wtdr/wODU4NDEwNnM0MTNkZmQzMXk1NDE%3D.jpg[/img]
Well its a bit tight in there, so gotta take out the AC this week. Steve hook me up with them directions you told me yesterday.
[img width=640 height=480]http://www.we-todd-did-racing.com/wetoddimage.wtdr/wODU4NDExNnM0MTNkZmQzMXk1NDE%3D.jpg[/img]
I was ------ around with this ----, gettin stuff ready for saturday!
[img width=640 height=480]http://www.we-todd-did-racing.com/wetoddimage.wtdr/wODU4NDEyNnM0MTNkZmQzMXk1NDE%3D.jpg[/img]
#5
Re: Turbo install prep began tonite, BLAH
My CAI on my 96 civic gets cut on that damn thing too. Luckily I noticed it after like a week and it had only gone through the paint and not the pipe yet. I just wrapped a shop rag around the part of the CAI and its been fine since. Are those nice wires and how much did they cost? I might hafta run down to Summit and buy me a set, I've been lookin for some nice ones. ---- looks nice mang, make sure to post up a finished product.
Thread
Thread Starter
Forum
Replies
Last Post
sohc-zc-14b-turbo
Turbo Parts For Sale
2
01-09-2004 12:45 PM