HomemadeTurbo - DIY Turbo Forum
Page 4 of 8
1
2
3
4
5
6
7
8
Show 40 post(s) from this thread on one page

HomemadeTurbo - DIY Turbo Forum (https://www.homemadeturbo.com/)
-   General Discussion (https://www.homemadeturbo.com/general-discussion-6/)
-   -   projekteg = boosted!!!!!!!!!*UPDATED AGAIN W/ DOWN PIPE PICS* (https://www.homemadeturbo.com/general-discussion-6/projekteg-%3D-boosted-%2Aupdated-again-w-down-pipe-pics%2A-19729/)

OnYx 04-30-2004 06:45 PM
Re:projekteg = boosted!!!!!!!!!
 
Originally Posted by shitbird
Finally,after 40000+ post.Looks good.

Ravage70 04-30-2004 06:57 PM
Re:projekteg = boosted!!!!!!!!!
 
teg i hope u dont blow ---- up

street_kings 04-30-2004 07:30 PM
Re:projekteg = boosted!!!!!!!!!
 
Good job Teg! Looks like we're at the same point, but i've got my OBD-I swap done already :P...i'll race ya to see who finishes first ;D j/k...

EDIT: When you do your OBD-I Swap, don't forget to rewire your IAB!

Carnesd 05-01-2004 02:33 AM
Re:projekteg = boosted!!!!!!!!!
 
Originally Posted by street_kings
Good job Teg! Looks like we're at the same point, but i've got my OBD-I swap done already :P...i'll race ya to see who finishes first ;D j/k...

EDIT: When you do your OBD-I Swap, don't forget to rewire your IAB!
You guys can't beat me, I ordered my last parts today, intercooler and stealthlines. I'll be boosted by the end of next week. 8)

crx2fast 05-01-2004 04:42 AM
Re:projekteg = boosted!!!!!!!!!
 
nice teg ;) glade to see your boosted
the charge pipes look butter. im diggin the flate black

projekteg 05-01-2004 10:26 AM
Re:projekteg = boosted!!!!!!!!!
 
Originally Posted by onyx
this is how you get them to fit. and ill see if i can find the howto i did a while back.

if you look at where the injector plugs into the harness there is a blue "guide" there. lake a small flat screwdriver and pop it off. then you will haveto take the middle pin off the DSM injector and shave teh corners off hte outside of the injector and your done, its a perfect, tight fit.
i tried that, i shaved the little clip on the inside of the dsm injector, shaved the corners a little and even mutilated my obd2 clip to almost nothing, and it still doesn't fit??? it's too late now since i tore the one clip up anyways, but yeah, i was thinking they would fit good if i just rounded the front corners, but, i don't know ???

BoosTedZSix 05-01-2004 11:44 AM
Re:projekteg = boosted!!!!!!!!!
 
Originally Posted by street_kings
Good job Teg! Looks like we're at the same point, but i've got my OBD-I swap done already :P...i'll race ya to see who finishes first ;D j/k...

EDIT: When you do your OBD-I Swap, don't forget to rewire your IAB!
i dont think he can use IAB's with a p28. i would just unplug the dam thing. iab's suck. from my own opinion car pulls harder without it. but it looks good projekteg. its about damn time. all those dam worthless posts about putting it together and its finally finished. although that diy sticker install was money. but yeah. congrats on finally finishing it. good luck with it. dont blow that bitch up.

projekteg 05-01-2004 11:50 AM
Re:projekteg = boosted!!!!!!!!!
 
what the ---- are iab's ???

45psi 05-01-2004 12:22 PM
Re:projekteg = boosted!!!!!!!!!
 
good job man

Chacko 05-01-2004 12:44 PM
Re:projekteg = boosted!!!!!!!!!
 
Originally Posted by BLACK_DEL_SOL
GOOD JOB MAN ;D im doing my engine swap next week and also going to boost with my new engine im going with 8 psi of boost :o should i change my fuel mangement ?
uhm yes


All times are GMT -5. The time now is 05:55 AM.
Page 4 of 8
1
2
3
4
5
6
7
8
Show 40 post(s) from this thread on one page


© 2024 MH Sub I, LLC dba Internet Brands