The Official HMT Highest Horsepower
Alright since there's more dyno queens than racers it would be nice to have a highest HP thread. ;) To qualify you must meet the following requirements:
1. Again this is for HMT members only so 150 post minimum 2. You must post a pic of you dynograph 3. Provide all the info possible, including your entire setup, elevation and what type of dyno used 4. To narrow things down only post if you are at least at 200HP So start posting up, I'm suprised there hasn't been another thread like this but I think its appropriate with all the dyno days comming up. ;) |
Re: The Official HMT Highest Horsepower
http://nehondatuning.com/pics/xenocron300whpLS-sm.jpg
Stock Block LS (B18b) SC34 57 trim Turbo @ 15psi Crome Tuning (done by yours truly of course) IP Mani 2.5" Downpipe and fully mandrel bent exhaust with CAT, 18" resonator and muffler JRC FMIC |
Re: The Official HMT Highest Horsepower
Could you add the setup/details too?
So far your in the #1 spot for highest HP. NE>NW :P |
Re: The Official HMT Highest Horsepower
oh oh , i need to get in on this sooner or later, just saving my spot on page one :6 , dunno how many people make more than 250whp :-*
|
Re: The Official HMT Highest Horsepower
Originally Posted by BoosTedZSix
oh oh , i need to get in on this sooner or later, just saving my spot on page one :6 , dunno how many people make more than 250whp :-*
Ok I just changed it cause I remembed most people run D's. Now more should qualify. |
Re: The Official HMT Highest Horsepower
does my superduty count?
|
Re: The Official HMT Highest Horsepower
1995 Neon
SOHC 2.0 eagle rods wiseco pistons 10.5to1 decked block milled head 1mm oversized valves crane came http://img215.echo.cx/img215/449/picture0036ii.jpg |
Re: The Official HMT Highest Horsepower
http://a5.cpimg.com/image/97/E3/5117...-02000180-.jpg
Stock GSR bottom Cometic .074 HG, 9.0ish C/R B16 Head, ITR cams & IM SC61 @ 15psi w/ a 16psi creep from 7800-8500 3" DP & Exh CROME w/ 550's and a walbro |
Re: The Official HMT Highest Horsepower
209whp/226wtrq @ 15psi
http://memimage.cardomain.net/member...99_81_full.jpg dynojet thanks to marysville speed and custom. -91 ford escort gt -J-spec 323 GTX turbo engine swap -J-spec 323 GTX engine harness -J-spec 323 GTX ECU -Custom 3" to 2.25" short ram turbo intake pipe -Custom 2.25" intercooler piping -Street Imports 18"x9"2.25" (core) FMIC -HKS SSQV blow-off valve -GT fuel rail -Walbro intank 255lph fuel pump -Corksport power series downpipe w/modified 3" tailend -3" mandrel bent downpipe back exhaust -Apex-I N1 turbo muffler -Corksport SS clutch line -ACT street/strip clutch -Modified Protege front motor mount -100% solid motor mounts -Turbo XS Single stage Manual boost controller -Mazdaspeed engine ground kit -NGK sparkplugs (one step colder) -A/C delete -C/C delete -No cat any questions PM me. NEUMAN |
Re: The Official HMT Highest Horsepower
Both these setups dont even exist anymore.
https://www.homemadeturbo.com/2003/b20turbo/b20dyno.jpg B20b (CRV) Stock Pistons/ Stock Rods (pinned block) B18c P72 GSR Head 5way Valve Grind (c/r is 9.5) Stock B20 Headgasket Custom Turbo Manifold T3/T4 .63ex/.50comp 57 trim (12psi) Tial 50mm BOV Tial 35mm WG 6psi 2.5 DP / 1.5 WG DP 3in Exhaust JG Edlebrock Intake manifold 64mm GSR T-body (proflowdesign) AN-R Intake manifold Gasket DSM 450cc Injectors w/ Zdyne GOLD SECU Tyrus 6in FMIC w/ 2.5 IC piping 5g Civic Radiator __________________________________ https://www.homemadeturbo.com/2005/dyno/IMG_0052.JPG JDM H22 w/ Factory LSD (stock head) Darton Sleeves 9.1 Endyn Rollerwave Pistons Eagle H Beam rods Balance Shafts Removed Turbonetics 62-1 Ball Bearing T3/T4 Turbo (22psi on the dyno) Tial 40mm Wastegate (12psi spring) Tial 50mm Blow off valve 2.5in Charge piping Custom Coach 8in IC Custom Turbo manifold w/ Shitbird Collector Stealthmode Oil line kit 3.0 in Mandrel Downpipe 950cc Venom Injectors Running OBD1 P28 w/ Uberdata I havent dyno'd my daily driver, but I'm sure its pretty close to 300 if not 300 around 22psi.. We'll have to have another dyno day soon.l |
Re: The Official HMT Highest Horsepower
^^^haha, thats one of Beau's graphs. Look at the TQ
|
Re: The Official HMT Highest Horsepower
i met the 150 posts requirement, so here's my most recent dyno sheet......
http://www.findjut.com/trumpet/dyno.jpg (yes.... i know my dynosheet looks different, but this is all they printed out for me) 302 HP & 183 FT/LBS@ 10 PSI B17A1 block balanced crank Crower Billet Rods Wiseco oversized Pistons 9.0:1 Compression Race Engineering Block Guard Cometic High Boost Head Gasket GS-R Head Crower dual valve springs Crower Titanium Retainers Ferrea Titanium Valves Stock GS-R Cams AEM Adjustable Cam Gears RC 370 cc fuel injectors Turbonetics T3/T4 Turbo 60 trim ssautonigshit manifold P61 ECU (stock ecu BITCHEZ) Apex-i V-AFC Apex-i AVC-R Vortec FMU (yes i have an FMU) i'm from PA.... so chalk one up for NE (i guess) |
Re: The Official HMT Highest Horsepower
wow, chris (xeno) maxed out his 450cc injectors at 300 whp. i bet your 370cc injectors are SCREAMING
Brett oh and i made 206whp/186tq, but i cant find the chart yet, so i wont post this officially yet |
Re: The Official HMT Highest Horsepower
i've got mine here:
http://www.we-todd-did-racing.com/we...ZkMzF5NTQx.jpg y7-stock internals 450cc 13t hf/std manifold 12psi spike @ 4k dropping to 10psi by 5k uberdata 1.66 here's a friend's car i tuned (don't know if it'll count, but i did make the power since i tuned it): http://www.we-todd-did-racing.com/we...ZkMzF5NTQx.jpg ls/vtec-9.5:1 880cc sc61 homemade ramhorn 26psi uberdata 1.70 |
Re: The Official HMT Highest Horsepower
150 post minimum. sorry.
|
Re: The Official HMT Highest Horsepower
whitey is going to delete that. but nice dyno
|
Re: The Official HMT Highest Horsepower
i don't have 150posts so it may not count, but i thought i'd post it up because it was my first home built pieced together turbo set-up.
crx88si: you're right. Even though you were very honest and polite, out of fairness no1 under 150 may be included ;) |
Re: The Official HMT Highest Horsepower
I think i may have the highest hp and tq for a d16a1. It is a D16a1 block, DOHC ZC head, rollerwaves (8.0:1), KRB shorty mani, t3/40e 57 trim at 16psi. The turbo doesn't hit the highest boost level till it redlines. The boost just keeps on rising and never sustains a constant psi.
Notice the dead spot. I have no idea what it is. The engine "pops" like a vtec crossover point. I've changed ecu's etc. THe clutch was also slipping on the dyno at the high end and I was getting bad ignition breakup on the other higher boost runs so there is more room for improvement. And it's 450's with an AFC II, BTM, and also a sds eic all tuned by me : http://www.we-todd-did-racing.com/we...ZkMzF5NTQx.jpg |
Re: The Official HMT Highest Horsepower
Originally Posted by xenocron
http://nehondatuning.com/pics/xenocron300whpLS-sm.jpg
Stock Block LS (B18b) SC34 57 trim Turbo @ 15psi Crome Tuning (done by yours truly of course) IP Mani 2.5" Downpipe and fully mandrel bent exhaust with CAT, 18" resonator and muffler JRC FMIC |
Re: The Official HMT Highest Horsepower
y8, 48/60, 19psi, afc hack :-X
235HP/222TQ Listen to the song if you want more info on the setup. :l |
Re: The Official HMT Highest Horsepower
Originally Posted by NYC86ZC
I think i may have the highest hp and tq for a d16a1. It is a D16a1 block, DOHC ZC head, rollerwaves (8.0:1), KRB shorty mani, t3/40e 57 trim at 16psi. The turbo doesn't hit the highest boost level till it redlines. The boost just keeps on rising and never sustains a constant psi.
Notice the dead spot. I have no idea what it is. The engine "pops" like a vtec crossover point. I've changed ecu's etc. THe clutch was also slipping on the dyno at the high end and I was getting bad ignition breakup on the other higher boost runs so there is more room for improvement. And it's 450's with an AFC II, BTM, and also a sds eic all tuned by me : http://www.we-todd-did-racing.com/we...ZkMzF5NTQx.jpg |
Re: The Official HMT Highest Horsepower
Originally Posted by Stealthmode
y8, 48/60, 19psi, afc hack :-X
235HP/222TQ Listen to the song if you want more info on the setup. :l ALSO. am I the only one who see's something wrong w/ the Neon's graph? |
Re: The Official HMT Highest Horsepower
^^^ I assumed it was spraying. On a 2nd look though, he coulda been the victim of a Hotrex dyno spike, haha
|
Re: The Official HMT Highest Horsepower
Originally Posted by leed
^^^ I assumed it was spraying. On a 2nd look though, he coulda been the victim of a Hotrex dyno spike, haha
|
Re: The Official HMT Highest Horsepower
so in other words you dont meet the minimum hp mark?
|
Re: The Official HMT Highest Horsepower
Originally Posted by leed
^^^haha, thats one of Beau's graphs. Look at the TQ
|
Re: The Official HMT Highest Horsepower
Dustin (turbohf)'s GTI. He's above the 3000 post mark so I assume he counts.
https://www.euronationmotorsport.com...6-05_300hp.jpg Stock '95 Jetta 2L ABA shortblock (135K on it) Stock 1.8L 16v head. 3 angle grind Stock ports Stock cams Stock MLS head gasket ARP Headstuds Ramhorn manifold 60/.63 T4 Tial 38 Johnnyracecar 25x8 sheetmetal intake VR6 throttle body 3" Downpipe 2-1/4 glasspack Megasquirt 16psi We've run it open downpipe at 25psi for several passes with no problems other than massive wheel spin. Shortblock: $65 Head: $25 |
Re: The Official HMT Highest Horsepower
heres mine.
http://home.comcast.net/~jcushingdc2...1/site1232.JPG devcon filled .10 over b16a srp pistons eagle rods gt35r precision 780s 29x9x3 cooler tial 38mm xoxo bov crome pro 21 psi |
Re: The Official HMT Highest Horsepower
whitey, maybe you could keep your original post updated with the current title holder in this thread. :8
|
Re: The Official HMT Highest Horsepower
Originally Posted by FooK
whitey, maybe you could keep your original post updated with the current title holder in this thread. :8
|
Re: The Official HMT Highest Horsepower
top 10 highest would be cool
|
Re: The Official HMT Highest Horsepower
Originally Posted by hotrex
top 10 highest would be cool
Originally Posted by FooK
whitey, maybe you could keep your original post updated with the current title holder in this thread. :8
I will when I get the time. Instead of complaing why don't you come up with the list than I'll post it in the first post? :8 |
Re: The Official HMT Highest Horsepower
Originally Posted by Whitey
I will when I get the time. Instead of complaing why don't you come up with the list than I'll post it in the first post? :8
|
Re: The Official HMT Highest Horsepower
Originally Posted by FooK
that wasnt a complaint diahrea head
|
Re: The Official HMT Highest Horsepower
This setup and car was sold but here is my built single cam with the bad Y8 head on 14 psi.
Vitaras, crower rods, Y8 head, Y7 block, BMC race manifold, 450s. Definitley was 250+ with the new z6 head, but never had it dynoed. And I never had it dynoed after I broke it in an ran 20 psi, this dyno was basically breaking in the motor. http://j-k-tuning.com/john.jpg |
Re: The Official HMT Highest Horsepower
[img][/img]
|
Re: The Official HMT Highest Horsepower
1 Attachment(s)
Stock B18b w/ ARP headstuds
SSAC Mani, 2.5" DP , 3" to es muffler Airesearch .60 .63 T3 , Tial wastegate DSM 450's Tuned on Chrome 8psi ** 263whp** Attachment 36144 |
Re: The Official HMT Highest Horsepower
im gonna call bs on a stock b18b making 263 on 8 psi with that small ass turbo :6
|
Re: The Official HMT Highest Horsepower
Just got it tuned at Intec on wednesday, I was suprised too. :)
|
Re: The Official HMT Highest Horsepower
If thats a stock head and what not, there is no way an LS carries TQ like that. No way thats 8psi all the way. Boost creep maybe? But who cares, 263 any way you cut it. Nice work.
|
All times are GMT -5. The time now is 08:19 PM. |
© 2024 MH Sub I, LLC dba Internet Brands