My DSM 450 install with a sneak peak (56K ????)
 

I just installed my DSM 450's, didnt have soldering skills so I used wire connectors ;) Tell me if this looks like I did it right.
When I put the 450's in, i just put a lil vasoline around the o-rings and put em in the fuel rail, and put em in place. They look like they have a little bit of space between the mani and injector, but i bolted down the fuel rail as much as i can, so I'm assuming its ok. ???


The 1st injector in place in the rail
[img width=700 height=500]http://www.we-todd-did-racing.com/wetoddimage.wtdr?i=wODkxMDc2NnM0MTNkZmQzMXk1NDE%3D[/img]

Little bit of vasoline will help them SLIDEEEE on in ;)
[img width=700 height=500]http://www.we-todd-did-racing.com/wetoddimage.wtdr?i=wODkxMDc3NnM0MTNkZmQzMXk1NDE%3D[/img]

See the space between the injector and mani? Is that normal?
[img width=700 height=500]http://www.we-todd-did-racing.com/wetoddimage.wtdr?i=wODkxMDc4NnM0MTNkZmQzMXk1NDE%3D[/img]

Wiring the clips and resistors up
[img width=700 height=500]http://www.we-todd-did-racing.com/wetoddimage.wtdr?i=wODkxMDc5NnM0MTNkZmQzMXk1NDE%3D[/img]

All done, just need to wrap them bitches up in electorical tape tomorrow
[img width=700 height=500]http://www.we-todd-did-racing.com/wetoddimage.wtdr?i=wODkxMDgwNnM0MTNkZmQzMXk1NDE%3D[/img]

A lil peak at the progress...(Yes i kno the mani is gay and says turbo on it, but i have a 2 year warranty on it, so deal with it :P )
[img width=700 height=500]http://www.we-todd-did-racing.com/wetoddimage.wtdr?i=wODgyODQ2NnM0MTNkZmQzMXk1NDE%3D[/img]

Looks nice dont it
[img width=700 height=500]http://www.we-todd-did-racing.com/wetoddimage.wtdr?i=wODgyODQ5NnM0MTNkZmQzMXk1NDE%3D[/img]


We ( as in buddy Adam hmt name 1SloSC2 and his dude Brandon)got all the charge piping done and welded, turbo, mani, fmic mounted, injectors in 8), ecu and harness installed, ac taken out , just need to run the oil lines, tap the oil pan, install the gauges and make the downpipe, hopefully it will all be done tomorrow

Re: My DSM 450 install with a sneak peak (56K ????)
 

See, you didn't need any help. :)

Re: My DSM 450 install with a sneak peak (56K ????)
 

Not bad. Setup is looking good and I bet you can't wait to rip on it 8) Oh yeah, those injectors are fine. They will look like they aren't in all the way but they don't leak. I noticed the same on my install.

Re: My DSM 450 install with a sneak peak (56K ????)
 

Do the injectors look ok tho? liek the spaceing and stuff?

Re: My DSM 450 install with a sneak peak (56K ????)
 

sweet! ;D ;D ;D

Re: My DSM 450 install with a sneak peak (56K ????)
 

I don't think my 450s stuck out like that, did you make sure you tightened the fuel rail down like you had a pair? be careful not to strip the studs though, I made that mistake and had to cut one of my fuel rail's nuts off.

Re: My DSM 450 install with a sneak peak (56K ????)
 

haha yea i tightened it down all the way, it will only let you go so far. Maybe mine look a little different cuz its a Y8?

Re: My DSM 450 install with a sneak peak (56K ????)
 

Looks good paul :D

Re: My DSM 450 install with a sneak peak (56K ????)
 

lolz. sorry just entertaining myself.

If you practice soldering, you can be a pro in like 2 minutes. It'd be worth the time and $5 for a radio nutsac 30w.

Re: My DSM 450 install with a sneak peak (56K ????)
 

could be, there are many differences between b and d.