My DSM 450 install with a sneak peak (56K ????)
 

I just installed my DSM 450's, didnt have soldering skills so I used wire connectors ;) Tell me if this looks like I did it right.
When I put the 450's in, i just put a lil vasoline around the o-rings and put em in the fuel rail, and put em in place. They look like they have a little bit of space between the mani and injector, but i bolted down the fuel rail as much as i can, so I'm assuming its ok. ???


The 1st injector in place in the rail
[img width=700 height=500]http://www.we-todd-did-racing.com/wetoddimage.wtdr?i=wODkxMDc2NnM0MTNkZmQzMXk1NDE%3D[/img]

Little bit of vasoline will help them SLIDEEEE on in ;)
[img width=700 height=500]http://www.we-todd-did-racing.com/wetoddimage.wtdr?i=wODkxMDc3NnM0MTNkZmQzMXk1NDE%3D[/img]

See the space between the injector and mani? Is that normal?
[img width=700 height=500]http://www.we-todd-did-racing.com/wetoddimage.wtdr?i=wODkxMDc4NnM0MTNkZmQzMXk1NDE%3D[/img]

Wiring the clips and resistors up
[img width=700 height=500]http://www.we-todd-did-racing.com/wetoddimage.wtdr?i=wODkxMDc5NnM0MTNkZmQzMXk1NDE%3D[/img]

All done, just need to wrap them bitches up in electorical tape tomorrow
[img width=700 height=500]http://www.we-todd-did-racing.com/wetoddimage.wtdr?i=wODkxMDgwNnM0MTNkZmQzMXk1NDE%3D[/img]

A lil peak at the progress...(Yes i kno the mani is gay and says turbo on it, but i have a 2 year warranty on it, so deal with it :P )
[img width=700 height=500]http://www.we-todd-did-racing.com/wetoddimage.wtdr?i=wODgyODQ2NnM0MTNkZmQzMXk1NDE%3D[/img]

Looks nice dont it
[img width=700 height=500]http://www.we-todd-did-racing.com/wetoddimage.wtdr?i=wODgyODQ5NnM0MTNkZmQzMXk1NDE%3D[/img]


We ( as in buddy Adam hmt name 1SloSC2 and his dude Brandon)got all the charge piping done and welded, turbo, mani, fmic mounted, injectors in 8), ecu and harness installed, ac taken out , just need to run the oil lines, tap the oil pan, install the gauges and make the downpipe, hopefully it will all be done tomorrow

Re: My DSM 450 install with a sneak peak (56K ????)
 

See, you didn't need any help. :)

Re: My DSM 450 install with a sneak peak (56K ????)
 

Not bad. Setup is looking good and I bet you can't wait to rip on it 8) Oh yeah, those injectors are fine. They will look like they aren't in all the way but they don't leak. I noticed the same on my install.

Re: My DSM 450 install with a sneak peak (56K ????)
 

Do the injectors look ok tho? liek the spaceing and stuff?

Re: My DSM 450 install with a sneak peak (56K ????)
 

sweet! ;D ;D ;D

Re: My DSM 450 install with a sneak peak (56K ????)
 

I don't think my 450s stuck out like that, did you make sure you tightened the fuel rail down like you had a pair? be careful not to strip the studs though, I made that mistake and had to cut one of my fuel rail's nuts off.

Re: My DSM 450 install with a sneak peak (56K ????)
 

haha yea i tightened it down all the way, it will only let you go so far. Maybe mine look a little different cuz its a Y8?

Re: My DSM 450 install with a sneak peak (56K ????)
 

Looks good paul :D

Re: My DSM 450 install with a sneak peak (56K ????)
 

lolz. sorry just entertaining myself.

If you practice soldering, you can be a pro in like 2 minutes. It'd be worth the time and $5 for a radio nutsac 30w.

Re: My DSM 450 install with a sneak peak (56K ????)
 

could be, there are many differences between b and d.

Re: My DSM 450 install with a sneak peak (56K ????)
 

all that matters is if they are sealed. ;)

Re: My DSM 450 install with a sneak peak (56K ????)
 

omg the pics are great...

loving the butt connectors and vasiline =)

Re: My DSM 450 install with a sneak peak (56K ????)
 

It seems like everybody who doesn't bore the seals out ends up with that space. I'm sure it's fine though.........
__________________
Best Car Insurance | Auto Protection Today | FREE Trade-In Quote

Re: My DSM 450 install with a sneak peak (56K ????)
 

I just used oil to lube mine up... 'cause I had that sitting around...

But hey, if you have vasoline handy, then might as well use it right?

The injectors don't have to be all the way in there, they are just a hair shorter than the stock injectors, as long as the seal is tight and the rail is on there good, you should be good to go!

Re: My DSM 450 install with a sneak peak (56K ????)
 

Nice use of the vasoline and i give you an A for color Coordination.

Re: My DSM 450 install with a sneak peak (56K ????)
 

rofl

that's sweet. vaseline is good for lube, huh?

Re: My DSM 450 install with a sneak peak (56K ????)
 

damn mabey i wont need to dremel anything out

Re: My DSM 450 install with a sneak peak (56K ????)
 

I snapped a fuel rail stud like nothing

Re: My DSM 450 install with a sneak peak (56K ????)
 

lol rock on

https://n00092.myspace.com/00092/90/51/92071509_m.jpg

Re: My DSM 450 install with a sneak peak (56K ????)
 

Yea. I was beginning to wonder that now, too. So really you don't have to dremel it out any? Just get some KY and slide 'em? :P Seriously though, you can serious keep it like that and then use petrolieum jelly ::) to slide them in and they work? Why would you dremel if that works then?


JP

Re: My DSM 450 install with a sneak peak (56K ????)
 

the only ting u have to drimmel is a little piece inside of the injector where the clips go

Re: My DSM 450 install with a sneak peak (56K ????)
 

What's the big deal with boring the seals out? I bored my stock 145K seals out with sand paper masking taped to a drill and my injectors sit flush and perfect.

Re: My DSM 450 install with a sneak peak (56K ????)
 

agreed i bored mine out with a dremel sanding barrel on my old setup. took like 4 minutes a piece if that.

Re: My DSM 450 install with a sneak peak (56K ????)
 

i have never bored them out, i always just tighten them down in, they always sit just fine.

Re: My DSM 450 install with a sneak peak (56K ????)
 

The Butt connectors wont affect anything with the resistors there?

Re: My DSM 450 install with a sneak peak (56K ????)
 

yeah whats so hard about boring out the seals? its not like it takes a long time. if it works i guess its coo then ;)

Re: My DSM 450 install with a sneak peak (56K ????)
 

+1 If it makes everything easier, I dont see why you'd want to skip that step.

Re: My DSM 450 install with a sneak peak (56K ????)
 

100 bucks says your upper seals tore when you put that fuel rail back on ;)

Re: My DSM 450 install with a sneak peak (56K ????)
 

what do u mean? how would they have tore?

Re: My DSM 450 install with a sneak peak (56K ????)
 

those edges are kinda sharp. it happened to me once. i just tightened it down a little more, and twisted the injector

Re: My DSM 450 install with a sneak peak (56K ????)
 

bore out the seals with a dremel or a drill sander thingy magigy and make it fit correctly. just make sure u test fit the injectors as you do it. dont overbore the sucker.

Re: My DSM 450 install with a sneak peak (56K ????)
 

since were on the 450cc subject, are they supposed to make alot of noise after the install