HomemadeTurbo - DIY Turbo Forum

HomemadeTurbo - DIY Turbo Forum (https://www.homemadeturbo.com/)
-   General Discussion (https://www.homemadeturbo.com/general-discussion-6/)
-   -   looky what i found.... (https://www.homemadeturbo.com/general-discussion-6/looky-what-i-found-72248/)

salesmonkey 01-07-2007 08:08 AM

Re: looky what i found....
 

Originally Posted by 78NOVA
well for power wise running naturally aspirated i hoped around anywhere from 300-450 horsepower. with such low compression though that my not be obtainable. ----, i can probably get around 600-800 horsepower with just 10-16 pounds of boost if my calculations are right. i only want to crank to boost up when someone is acting a ass and thing they can play with me. id really only run 2-5 pounds street and crank it at the track.

once you feel what the car has it will be hard to leave it at only 2-5 pounds on the street. but probilby more streetable if you did lol.

thiggyperformance 01-07-2007 12:02 PM

Re: looky what i found....
 
i think 300+ is very do-able in this day and age with all the nice heads very cheap. if you were to run some double hump heads it should be easy too but finding a set that has not been milled to ---- will be hard.

78NOVA 01-07-2007 04:05 PM

Re: looky what i found....
 
im gonna use my dads cast steel heads rebuilt to 202's and a very good port and polish job. i use the parts that i stated earlier i will have me one hefty powerhouse under the hood without the turbos.

thiggyperformance 01-07-2007 04:18 PM

Re: looky what i found....
 

Originally Posted by 78NOVA
im gonna use my dads cast steel heads rebuilt to 202's and a very good port and polish job. i use the parts that i stated earlier i will have me one hefty powerhouse under the hood without the turbos.

what are the castings and cc's of that fore mentioned heads

78NOVA 01-07-2007 04:30 PM

Re: looky what i found....
 
im not sure yet, my dad has two sets. i havent looked at them yet because i wanted to get the motor apart first and then figure out what parts i need and go from there. i need piston rings lol, and i also need rod bearings. itll get done little by little. i may be getting the heads redone next week restored back to stock specs with fresh valves and springs. so i have a better motor than the 305.

thiggyperformance 01-07-2007 04:42 PM

Re: looky what i found....
 
yea the 305's are eaaaa ok i guess if that is all you got to work with. if I do another chevy it will be a destroked 400 now that would be a good turbo motor

78NOVA 01-07-2007 06:23 PM

Re: looky what i found....
 
theres a guy on thirdgen.org that has a built 305 running 11 second quarter miles times on slicks in has camaro. looks/sounds stock too thats the bad part.

thiggyperformance 01-07-2007 06:25 PM

Re: looky what i found....
 

Originally Posted by 78NOVA
theres a guy on thirdgen.org that has a built 305 running 11 second quarter miles times on slicks in has camaro. looks/sounds stock too thats the bad part.

so what does he have done to it nos?

Tough-guy 01-07-2007 08:17 PM

Re: looky what i found....
 
^^^I was gonna say it was probably sprayed like mycrx's mom in a golden shower.

AMkrew 01-07-2007 11:44 PM

Re: looky what i found....
 
there's too much domestic chat in here. I didn't see ONE mention of a honda, so I vote this thread gets locked! :P

Sounds like a good plan. A turbo'd sbc is no joke. I just never really got how a carbuerated vehicle is tuned. I guess I'm too new school... :'( Some sort of rising rate fpr? MSD BTM?
-josh-


All times are GMT -5. The time now is 12:49 AM.


© 2024 MH Sub I, LLC dba Internet Brands