Just checkin in... few pics,vids, carnage included
#1
Just checkin in... few pics,vids, carnage included
Just floating through the forum, haven't been here in a while.
The cavalier was doing quite well up until a couple months ago. Finished the header/exhaust, smaller pulley etc. Went to the JCO bash in Canada and had a mishap.
With a 3.0 pulley and the exhaust I was running 13.9/14.0's at 101.6 Installed the 2.8 pulley (14-15psi) and ran:
Made three passes with terrible 60 fts on street tires: 14.0@104.22 13.9@104.88 and the last one.... 13.9@
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
I wonder what that last pass would have been... threw a rod at the 1k ft mark 13.9 coasting to 94mph
That was a fun tow from Canada to Michigan DOH!
I didn't have time to build an engine for it so I threw another stocker in and reverted back to the 3.0 pulley. Same setup I used to run 13.9's with I can only muster 14.5@98.7 I need to figure out whats up but this motor is "the suck"
Well I did manage to acquire a video of the car with the 2.8 pulley while it was alive, car was really starting to feel good.
http://www.airtonics.com/cavalier/vi...yinstalled.wmv
Oh and guys, if you recall there used to be no tuning software for jbody cars. HP tuners currently has something available. I've been using it for a lil while, decent program. No wiring and control over fuel/timing maps, rev limiters, speed gov, fan on and off points etc. Huge improvement over my emanage which is now doing nothing.
When browsing the forum it's amusing, I see only a few names I recogonize, so most probably have no idea who I am.
Hope all is going well in the HMT world...
The cavalier was doing quite well up until a couple months ago. Finished the header/exhaust, smaller pulley etc. Went to the JCO bash in Canada and had a mishap.
With a 3.0 pulley and the exhaust I was running 13.9/14.0's at 101.6 Installed the 2.8 pulley (14-15psi) and ran:
Made three passes with terrible 60 fts on street tires: 14.0@104.22 13.9@104.88 and the last one.... 13.9@
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
I wonder what that last pass would have been... threw a rod at the 1k ft mark 13.9 coasting to 94mph
That was a fun tow from Canada to Michigan DOH!
I didn't have time to build an engine for it so I threw another stocker in and reverted back to the 3.0 pulley. Same setup I used to run 13.9's with I can only muster 14.5@98.7 I need to figure out whats up but this motor is "the suck"
Well I did manage to acquire a video of the car with the 2.8 pulley while it was alive, car was really starting to feel good.
http://www.airtonics.com/cavalier/vi...yinstalled.wmv
Oh and guys, if you recall there used to be no tuning software for jbody cars. HP tuners currently has something available. I've been using it for a lil while, decent program. No wiring and control over fuel/timing maps, rev limiters, speed gov, fan on and off points etc. Huge improvement over my emanage which is now doing nothing.
When browsing the forum it's amusing, I see only a few names I recogonize, so most probably have no idea who I am.
Hope all is going well in the HMT world...
#5
Re: Just checkin in... few pics,vids, carnage included
Sunfire was sold with the bad motor....
I purchased another engine from a local yard for $650 Also upgraded to a spec S3+ clutch and a fidanza lightened flywheel. Which is also why I'm upset it's slower because it should be better off at this point.
I still have the old head (which is in good shape) I'm hoping to build an engine for it this winter.
I purchased another engine from a local yard for $650 Also upgraded to a spec S3+ clutch and a fidanza lightened flywheel. Which is also why I'm upset it's slower because it should be better off at this point.
I still have the old head (which is in good shape) I'm hoping to build an engine for it this winter.