HomemadeTurbo - DIY Turbo Forum

HomemadeTurbo - DIY Turbo Forum (https://www.homemadeturbo.com/)
-   Forced Induction (https://www.homemadeturbo.com/forced-induction-7/)
-   -   turbo project done...car won't start... what to do??? (https://www.homemadeturbo.com/forced-induction-7/turbo-project-done-car-wont-start-what-do-21451/)

pa2play 06-03-2004 01:01 PM

Re:turbo project done...car won't start... what to do???
 
yes still taking it to the dyno, next wed. at 2pm ;) can't wait. i'm trailering it their...like 1 1/2 hrs away :'( Michigan sucks!

chingro4u 06-03-2004 01:01 PM

Re:turbo project done...car won't start... what to do???
 

Originally Posted by pa2play
ok, I set it at chingro4u's settings and it started after a few mins of trying. It's a little rough, idles about 1100-1200, then when I just bump that gas it's rough. oil press was good for a few mins, then dropped down to 50psi, so i'm gonna add 1/4 qt. in and see what happens. i'll report back later.

ok now that it starts, go to the LO throttle setting, and at the 1000 RPM mark, play with the setting and find where your engine idles ok. if you have a stock pump and fuel pressure regulator, your engine should have a good idle mark betwwen -27 and -42, somewhere around those marks....

happy boosting....

chingro4u 06-03-2004 01:05 PM

Re:turbo project done...car won't start... what to do???
 
ig your motor and turbo setup is good, and you are only worried about the tunning aspect of the car,

YOU DONT NEED TO TRAILER IT, U CAN DRIVE IT (dont rape it on the way, just drive it moderately)....

SAVE THE MONEY, when u find the idle, just set it accross the board on that setting, and drive it to the dyno.

(i recommend using hte money u saved and install a high volume fuel pump, so u can get some good numbers from the dyno)

pa2play 06-03-2004 02:54 PM

Re:turbo project done...car won't start... what to do???
 
will a walbro 255 pump really help thatmuch?

pa2play 06-03-2004 03:54 PM

Re:turbo project done...car won't start... what to do???
 
ok, went out for my first drive, I set my settings at lo -37 and high -39, let me know if I should change anything. I have an ajustable wg and right now it was hitting about 10 psi, but the second it would get to that I would let off the gas.

chingro4u 06-03-2004 03:56 PM

Re:turbo project done...car won't start... what to do???
 

Originally Posted by pa2play
ok, went out for my first drive, I set my settings at lo -37 and high -39, let me know if I should change anything. I have an ajustable wg and right now it was hitting about 10 psi, but the second it would get to that I would let off the gas.

it should be the other way around

-37 is richer (more gas) than -39.

lo should be -39 and hi be -37


the pump should be a MUST to keep the setup SAFE.
people have gotten away with a stock pump, but it is up to u to take the chance.

pa2play 06-03-2004 04:02 PM

Re:turbo project done...car won't start... what to do???
 
man, I sick of spending $ on this car. I already have 1200 in the turbo set up :'( If I get it tuned, then get a fuel pump later, will I have to get it tuned again?

iNetForce 06-03-2004 10:00 PM

Re:turbo project done...car won't start... what to do???
 
hey man, u have spent 1200 on that car, if u spend 2000 ur still way lower than stupid people paying thousands of dollars to a shop to get a turbo installed, nobody cant buy ur knowledge. They more u pay and do, the more u know.

knowledge, priceless.

dont give up!

pa2play 06-03-2004 10:17 PM

Re:turbo project done...car won't start... what to do???
 
ok, I have it set at lo -37 and hi-36, when i go into boost runs fine, but when I come out of it, it idles VERY low, why?

iNetForce 06-03-2004 10:54 PM

Re:turbo project done...car won't start... what to do???
 
sounds like timing is too retarded or too advanced for me, does it take a while for the rpms to go up and then to drop down?



All times are GMT -5. The time now is 03:24 PM.


© 2024 MH Sub I, LLC dba Internet Brands