turbo identification and a few questions..chingchong meow or turbonetics?
10-23-2006, 07:44 PM
#11
1.0 BAR
Join Date: Mar 2006
Posts: 426
Re: turbo identification and a few questions..chingchong meow or turbonetics?
ya know what after thinking about it some more, you probably could push that turbo farther just not sure about 400 though.....i would expect you would be pushing 20+psi to do it with that turbo....pm blaast he will be better equipped to answer this question
10-23-2006, 10:33 PM
#14
1.5 BAR
Join Date: Oct 2004
Posts: 877
Re: turbo identification and a few questions..chingchong meow or turbonetics?
Yes it's a good size for your setup.
everything looks repairable.
Simply looks like this turbo somehow lost it's balance and prematurely lost it's balancing.
machining the shaft and undersize bearings will be needed. that's no extra cost.
you'll end up better than with a chinese turbo.
everything looks repairable.
Simply looks like this turbo somehow lost it's balance and prematurely lost it's balancing.
machining the shaft and undersize bearings will be needed. that's no extra cost.
you'll end up better than with a chinese turbo.
10-24-2006, 11:40 AM
#15
1.5 BAR
Thread Starter
Join Date: Feb 2005
Posts: 1,181
Re: turbo identification and a few questions..chingchong meow or turbonetics?
Originally Posted by BLAAST
Yes it's a good size for your setup.
everything looks repairable.
Simply looks like this turbo somehow lost it's balance and prematurely lost it's balancing.
machining the shaft and undersize bearings will be needed. that's no extra cost.
you'll end up better than with a chinese turbo.
everything looks repairable.
Simply looks like this turbo somehow lost it's balance and prematurely lost it's balancing.
machining the shaft and undersize bearings will be needed. that's no extra cost.
you'll end up better than with a chinese turbo.
10-24-2006, 01:09 PM
#16
3.0 BAR
Join Date: Mar 2006
Posts: 5,631
Re: turbo identification and a few questions..chingchong meow or turbonetics?
Originally Posted by Turdbo
so your asying my turbo that i have is acutally a good turbo for my power goals if i change the compressor side of the turbo?
Mine also had the bogus T cast in it (they rip off EXACT castings)....
Mines a 48/50 ar... 57 trim stage 3 wheel.
Good luck.
10-24-2006, 10:10 PM
#18
1.5 BAR
Thread Starter
Join Date: Feb 2005
Posts: 1,181
Re: turbo identification and a few questions..chingchong meow or turbonetics?
Originally Posted by ososlohatch
(\__/)
(o.O ) Z
(> < )/ ching chang meow bitchhhhhhhhhhhhhhhhhhhhhhhh
(o.O ) Z
(> < )/ ching chang meow bitchhhhhhhhhhhhhhhhhhhhhhhh
Originally Posted by bigdaddyvtec
I bought the exact same looking turbo.. It IS ching change yellow meow... BUT I bought a garret center section for mine... MADE DAMN GOOD POWER on it oo.. STock f22b1, 305 WHP and 307 tq@ 15 PSI. Id say 400 is doable, but itll take around 25 psi to see it. Get it rebuilt, itll work fine foir you and your goals.
Mine also had the bogus T cast in it (they rip off EXACT castings)....
Mines a 48/50 ar... 57 trim stage 3 wheel.
Good luck.
Mine also had the bogus T cast in it (they rip off EXACT castings)....
Mines a 48/50 ar... 57 trim stage 3 wheel.
Good luck.
...i didnt want to buy a new turbo
Thread
Thread Starter
Forum
Replies
Last Post
dasfinc
Forced Induction
4
07-21-2008 02:26 PM
scottsi
General Discussion
31
04-02-2006 09:14 PM
