HomemadeTurbo - DIY Turbo Forum

HomemadeTurbo - DIY Turbo Forum (https://www.homemadeturbo.com/)
-   Forced Induction (https://www.homemadeturbo.com/forced-induction-7/)
-   -   question about dsm 450 install (https://www.homemadeturbo.com/forced-induction-7/question-about-dsm-450-install-27630/)

alwaystootall 10-06-2004 08:32 PM

question about dsm 450 install
 
i didnt know if this should go here or in the engine man. sectiion. but anyways....
i put some 450s in my 91 civic today,and had a few questions.
- the write up on the site says to get some taller bottom seals and bore them out. i just used some b16 bottom seals and bored them out, and was woundering if i would have any problems with those.
-i put the injectors in and they fit fine except where they go into the fuel rail. the slid in fine,and i tightened down the fuel rail, but in between the rail and the injector
seal(quess thats what it is. its the smaller round black seal ontop of the injector) there is a little gap. just woundering if this is normal.
thanks

turboboy 10-06-2004 08:34 PM

Re:question about dsm 450 install
 
meaning the top seal isnt tight?...thats not cool. and as for the lower seals, its fine so long as the dsm injectors end up sticking into the manifold as much as the stock ones did

alwaystootall 10-06-2004 08:41 PM

Re:question about dsm 450 install
 
well the o-ring that goes into the fuel rail is tight, its the black seal right below that...

turboboy 10-06-2004 08:44 PM

Re:question about dsm 450 install
 
oh...the spacer thing? is the injector maybe too far down in there and the rail cant tighten down on it enough?...if the injectors are tight in there that spacer shouldnt matter much imo...but i dunno

alwaystootall 10-06-2004 09:10 PM

Re:question about dsm 450 install
 
well the injector sits snug(looks nice and normal) in the intake manifold. but im not using the taller seals. the rail is flush with the plastic pieces that sit on the intake manifold where the studs are to put the nuts on. everything look fine but the gap in between the fuel rail and the black seal on the injector.(the one right befor the injector gets fat)

turboboy 10-06-2004 09:12 PM

Re:question about dsm 450 install
 
did you check the overall injector height compared to stock?...you may want some taller seals

Dr.Boost 10-06-2004 09:14 PM

Re:question about dsm 450 install
 
I think that's normal. Mine have a gap and they don't leak so ---- it. As long as your O-rings are good you should be fine.
__________________
Best Car Insurance | Auto Protection Today | FREE Trade-In Quote

turboboy 10-06-2004 09:15 PM

Re:question about dsm 450 install
 
im paranoid about fuel ---- after my friends del sol went up in flames because of leaky injector seals :-\...i dont like it when they can move

Curtis2kul 10-06-2004 09:16 PM

Re:question about dsm 450 install
 
can you post some pics of the finall install cause im going to be putting mine in in a couple of days!

Dr.Boost 10-06-2004 09:19 PM

Re:question about dsm 450 install
 

Originally Posted by ghettoturbo
im paranoid about fuel ---- after my friends del sol went up in flames because of leaky injector seals :-\...i dont like it when they can move

The stock ones move too. :-\
__________________
Best Car Insurance | Auto Protection Today | FREE Trade-In Quote


All times are GMT -5. The time now is 04:42 PM.


© 2024 MH Sub I, LLC dba Internet Brands