1/2in heim, 12mm bolt, home made traction bar... how to get rid of play?
#12
Re: 1/2in heim, 12mm bolt, home made traction bar... how to get rid of play?
easy.
1 go to shops, get 2 of 1/2" bolts (cheaper the better, get em long too...)
2 screw into heim, cut off heads flush with top of heim,
3 put 1/8"chamfer around newly cut bolt (for weld channel...)
4 plug weld them in, both ends.
5 drill / tap m12 straight down through the bolts
6 done, beer time.
1 go to shops, get 2 of 1/2" bolts (cheaper the better, get em long too...)
2 screw into heim, cut off heads flush with top of heim,
3 put 1/8"chamfer around newly cut bolt (for weld channel...)
4 plug weld them in, both ends.
5 drill / tap m12 straight down through the bolts
6 done, beer time.
#16
Re: 1/2in heim, 12mm bolt, home made traction bar... how to get rid of play?
still got wheel hop w/ the 15's at 40psi... i got out of it real quick. haha need to keep that tranny alive.
kinda annoying... hopfully the tire store pulls through with the slicks today
internet at home is gone... someone found out what a wireless password is...
kinda annoying... hopfully the tire store pulls through with the slicks today
internet at home is gone... someone found out what a wireless password is...
#17
Re: 1/2in heim, 12mm bolt, home made traction bar... how to get rid of play?
Originally Posted by danz
still got wheel hop w/ the 15's at 40psi... i got out of it real quick. haha need to keep that tranny alive.
kinda annoying... hopfully the tire store pulls through with the slicks today
internet at home is gone... someone found out what a wireless password is...
kinda annoying... hopfully the tire store pulls through with the slicks today
internet at home is gone... someone found out what a wireless password is...
fucken call them and bitch that the season is almost over and you need them for this friday, are you using the other 14s?
hahahahahah and you were even nice enough to give them the up date
call telus get your ---- hooked up
#18
Re: 1/2in heim, 12mm bolt, home made traction bar... how to get rid of play?
------ tire shop... dropped the ball.
slicks wont be here till next week tuesday. ---- off.
gonna roll off the line on friday. boo
the wheel hop wasnt BAD but it was there... lets just say i was worried about the tranny. lol.
yeah im gonna rock the street tires at like 25psi to start. see how that goes.
slicks wont be here till next week tuesday. ---- off.
gonna roll off the line on friday. boo
the wheel hop wasnt BAD but it was there... lets just say i was worried about the tranny. lol.
yeah im gonna rock the street tires at like 25psi to start. see how that goes.
#19
Re: 1/2in heim, 12mm bolt, home made traction bar... how to get rid of play?
This one is easy. I would first say to use a metric heim, but find swaged tubing in m12 is damn near impossible. Also if you ever need anything www.mcmaster.com is the bible.
Second, I did a bit of conversion and the gap your looking to make up is .7mm or .0275". What you need is a piece of pipe or tube with a wall thickness of .0275. Your likely to find thin copper or aluminum piping with those specs. Just cut yourself a small piece and slip it over the bolt. Problem solved. I had to do the same when my shocks had some play while trying to put them into the forks, it was just a little bigger..
Second, I did a bit of conversion and the gap your looking to make up is .7mm or .0275". What you need is a piece of pipe or tube with a wall thickness of .0275. Your likely to find thin copper or aluminum piping with those specs. Just cut yourself a small piece and slip it over the bolt. Problem solved. I had to do the same when my shocks had some play while trying to put them into the forks, it was just a little bigger..
Thread
Thread Starter
Forum
Replies
Last Post
SpankedYA!
Fabrication
120
02-03-2008 06:31 PM
TinyTubs
Fabrication
27
02-22-2007 02:06 AM
Xgenturbo
General Discussion
6
07-22-2006 12:44 PM
HMT-Admin
Hybrid/Tech
0
10-11-2005 08:17 AM