Re:Who is tuning TurboEdit setup(s) with a Wideband, need semi-tuned Maps
 

oops;

yeah reading is over rated....

Re:Who is tuning TurboEdit setup(s) with a Wideband, need semi-tuned Maps
 

So just Leed, Jason and myself?

Re:Who is tuning TurboEdit setup(s) with a Wideband, need semi-tuned Maps
 

Dustin is WB tuning...

Though I haven't seen him for a few days.

A local guy to me "beaterKU" will be WB tuning also.

Re:Who is tuning TurboEdit setup(s) with a Wideband, need semi-tuned Maps
 

You get ROMulator support added back? I desparately need it this weekend. Plus I am tuning a turbo ZC next week I think and that would save loads of time.

Perty please ;D

Re:Who is tuning TurboEdit setup(s) with a Wideband, need semi-tuned Maps
 

Oh fine....

I'll come up with something.

Re:Who is tuning TurboEdit setup(s) with a Wideband, need semi-tuned Maps
 

I usually just keep the Romulator software open at the same time and update it with that...but using the TE feature would be cool...
:P

Re:Who is tuning TurboEdit setup(s) with a Wideband, need semi-tuned Maps
 

Since I changed to the new backend.. ROMulator support changed slightly in dealing with the ROM Properties.

The tables didn't change at all.. actualyl amde for LESS code. :D

But I have to rewrite the ROM properties verification routine. This won't take too long.. I'm working on it right now. I should have something available in a few hours.

Re:Who is tuning TurboEdit setup(s) with a Wideband, need semi-tuned Maps
 

...all done...

2.0.11 -> Redownload chief.

Re:Who is tuning TurboEdit setup(s) with a Wideband, need semi-tuned Maps
 

I have about 20 hours of wideband time in on the B18B/turbo map I posted on PGMFI. Most of it is vacuum / cruise / fuel economy related however. The boost region is perfectly safe... wobbles between 11.5 and 12 AFRs. Timing is straight up step retard - could probably use more work.
97 B18B motor, 91 B18A intake mani, SSAC tubular, .48ARhot/.63AR compressor .50trim Saab T3, 3" DP, 3" stainless exhaust, Apexi N1 3"in/4" out muffler, walbro 255 lph fuel pump, DSM 450s, stock FPR - no fuel pressure guage, stock fuel return, stock fuel filter, starion IC. Tune = DB09.exp ECU = 91 PM6

I have about 1 hour of widebanding on the PM6 tune that I posted on PGMFI. I took Leed's advice (-12% from my LS tune) and then did a little further refining of 1900-3000 RPM (was too rich) and 6300+ RPM (again, too rich), idle (too rich) and then did some work to try to get a gradual transition from 13.5 AFR at 0psi to 11.5 AFR @10spi. Step retard. Pretty ------- decent tune for how quick it was done.
Stock D16A6 motor, Y8 intake manifold, 62mm ITR TB, Volvo 760 T3 turbo, Saab Viggen IC, DSM 450cc injectors, 38psi FP @ idle with stock FPR + walbro 255 pump. Ran 1700ish lb 89 HF CRX to 13.14@107mph Was run on "T85" (1 gallon tolulene / 4 gallons BP93) for safety purposes so I don't know if it is pump gas-friendly (although I would expect it is.) Tune = Foowee3.exp ECU = 91 PS9 (converted to PM6)

Re:Who is tuning TurboEdit setup(s) with a Wideband, need semi-tuned Maps
 

I shall be spending a good 4 hours tomorrow on the new PM6 and PM7 versions of code with my setup.

Upping the boost to 8....um maybe 10:) and tuning on both the PR4 and PM6 ecus.

Then next week if this guy doesnt fall through, I should have a nice ZC tune ready to post.

I hope the code doesnt change much anymore ???