Go Back  HomemadeTurbo - DIY Turbo Forum > Homemadeturbo > Engine Management
ill pay if someone figures out my datalogging problem >

ill pay if someone figures out my datalogging problem

Engine Management eCtune , Crome , AFC , FMU , Zdyne , Hondata , EMS , TE , Uberdata Anything to control your fuel, spark needs!

ill pay if someone figures out my datalogging problem

Old 04-02-2006, 07:34 PM
  #1  
0.0 BAR
Thread Starter
 
Join Date: Mar 2006
Posts: 42
Default ill pay if someone figures out my datalogging problem

ill pay someone $50 to get datalogging to work correctly in uberdata or ecucontrol. my cable works my ecu works and i have the correct driver for my computer and cable because i tested it. im just wondering if there is a trick or something to get datalogging working in ub i get messed up values. my j12 is connected when i try datalog in uberdata. what settings do i put which com port? i live in az. but if you say something on here and it gets my datalogging working ill still pay via paypal. Thanks.
t3t4 is offline  
Old 04-02-2006, 08:12 PM
  #2  
1.5 BAR
 
Join Date: Aug 2003
Posts: 1,068
Default Re: ill pay if someone figures out my datalogging problem

let me know if you get it working I have the same problem and I could not get it to work either. please guys post up on this.
shanerv is offline  
Old 04-02-2006, 08:32 PM
  #3  
0.0 BAR
 
Join Date: Feb 2003
Posts: 0
Default Re: ill pay if someone figures out my datalogging problem

u guys post on www.pgmfi.com ?
R-MAK is offline  
Old 04-02-2006, 08:58 PM
  #4  
0.0 BAR
Thread Starter
 
Join Date: Mar 2006
Posts: 42
Default Re: ill pay if someone figures out my datalogging problem

yes i do. i got ecucontrol to work i set it to com 5 put my usb cable in the number 3 hole. took out the jumper on j12 but it takes about 5 seconds for it to respond. like if my car is idling it notices the rpm and it knows my mph but it takes along time for it to respond my setting was at 38400 should i go up or down?
t3t4 is offline  
Old 04-03-2006, 01:35 AM
  #5  
0.0 BAR
 
Join Date: Oct 2005
Posts: 0
Default Re: ill pay if someone figures out my datalogging problem

Short J12.

Set port speed to 38400 bps.

Depending on who's cable you bought the RX and TX may be backwards on the cable end.

Set your COM port for the USB cable in wdows to 1,2,3 or 4.

Set you COM port in UD to the same port.

If you have already done these things then I will double check the settings on my laptop and post them up.

I also have the best luck with just a bare bones OS installation. I can get it to run with the OEM software package, but it seems to be much more reliable without all the extra crap programs running in the background.
JonDouglas is offline  
Old 04-03-2006, 10:13 AM
  #7  
1.5 BAR
 
Join Date: Aug 2004
Posts: 949
Default Re: ill pay if someone figures out my datalogging problem

For Uberdata, I think the wires are (1 thru 5):
1 - Ground
2 - TXD
3 - Power
4 - RXD
5 - Unused

For Crome, I'm hoping it's the same but switching TXD & RXD. I haven't gotten it to work yet.

Make sure you're selecting the O2 check box too.

Oh yeah, do you have a wideband?
95RedEX is offline  
Old 04-03-2006, 10:34 AM
  #8  
0.0 BAR
 
Join Date: May 2005
Posts: 0
Default Re: ill pay if someone figures out my datalogging problem

You didn't mention what version you were using. Don't use 1.9x. The datalogging is broken in the executable. Go to uberdata.pgmfi.org and search for uberdata1.7ost2. This version works very well and has the ostrich support.

To rid any errors in hooking up the DL cable, just twist both the RX and TX wires together. Don't worry about connecting J12, you will be essentially doing that by by putting RX and TX together. First check to see if the cable works by using hyperterminal. Open hyperterminal and select the port that it is on and try typing on the keyboard. If you see what you typing then the cable is working properly. If it doesn't work then check to make sure you have the RX and TX wires. Start by checking random wires (EXCEPT THE POWER AND GROUND WIRES).

After you have gotten the cable to work correctly, connect it to the ECU. Open uberdata and open your bin. Select the COM port that you are using in the drop down box. Select the TPS check box. Turn the car to the ON position. The TPS value should be around 10. Hit the throttle and see of the value changes. IF it doesn't work, go back and check your wiring again, and go though the steps again.

Hope you get it to work.
0b00st0 is offline  
Old 04-03-2006, 09:18 PM
  #9  
0.0 BAR
Thread Starter
 
Join Date: Mar 2006
Posts: 42
Default Re: ill pay if someone figures out my datalogging problem

im using 1.7, j12 is connected and tried com 1-4. i used hyper terminal and it worked which means my cable and driver are good right? im using windows xp.. i think im going to try use my computer instead of my laptop. i did get ecucontrol to datalog but it only gave me values like every 5 seconds but they were correct and it was on com 5. but i cant get the datalogging thing to log anything and its to slow to do anything with.
t3t4 is offline  
Old 04-03-2006, 09:29 PM
  #10  
0.0 BAR
 
Join Date: Mar 2004
Posts: 0
Default Re: ill pay if someone figures out my datalogging problem

What cable are you using? I have the DKU-5 and it only works on COM 6. Which means it works in EC control but not in Uberdata. If I force it to COM 3 or 4 it doesnt work either. I have to mess with it when I get my new motor back in and I will let you know what works for me.
SpankedYA! is offline  

Thread Tools
Search this Thread
Quick Reply: ill pay if someone figures out my datalogging problem


Contact Us - Sitemap - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.