CromePro, Drivers, ??? HELP ?
#1
CromePro, Drivers, ??? HELP ?
Ok, so i have CromePro, a Moates chip burner, and a datalogging 4pin cable.
I have a P28 in a fully built turbo'd D16z6.
My question: My ECU was chipped with a Basemap From Phearable.net... How do i tune off of that basemap? i dont have the map on my laptop, and i dont think u can get the Map off the chip through the burner can you? or do you get it through datalogging?
ALSO... my datalogging cable wont datalog~ Why is this? I think i downloaded the right driver off Xenocron but i'm not sure how you save the drivers in certian folders etc.~ Can u save them just anywhere?
Do i need to set the port for the cable through CromePro? How?
And .... Do i have boost tools already because i have CromePro now?
Where can i download "boost tools" and the drivers? Can you give me a link?
ONE MORE THING: I had the basemap done by Phearable, but my idle is 18+ a/f. BAD... I asked him to burn it for an AEM uego wideband. BUT>>> the ECU is seeing the signal from the STOCK o2 sensor. Not the wideband... Should i change it so the ECU see's the signal from the wideband?
I know how to tune~ Just not how to setup the Computer drivers and all this ----~
Thanks~
I have a P28 in a fully built turbo'd D16z6.
My question: My ECU was chipped with a Basemap From Phearable.net... How do i tune off of that basemap? i dont have the map on my laptop, and i dont think u can get the Map off the chip through the burner can you? or do you get it through datalogging?
ALSO... my datalogging cable wont datalog~ Why is this? I think i downloaded the right driver off Xenocron but i'm not sure how you save the drivers in certian folders etc.~ Can u save them just anywhere?
Do i need to set the port for the cable through CromePro? How?
And .... Do i have boost tools already because i have CromePro now?
Where can i download "boost tools" and the drivers? Can you give me a link?
ONE MORE THING: I had the basemap done by Phearable, but my idle is 18+ a/f. BAD... I asked him to burn it for an AEM uego wideband. BUT>>> the ECU is seeing the signal from the STOCK o2 sensor. Not the wideband... Should i change it so the ECU see's the signal from the wideband?
I know how to tune~ Just not how to setup the Computer drivers and all this ----~
Thanks~
#4
Re: CromePro, Drivers, ??? HELP ?
no spoon feeding needed~ I just had some idiot questions~ i have most of it worked out myself...
I've tuned w/ Uber... But it's the whole setting up the ---- that i dont get and getting hardware working in sinc. I'm the kind of guy that saves things off the internet and can never find them again~ That kinda ----.
I still cant figure out why my datalogging cable wont work... It might be my harddrive~ It's been replaced since i had Uber... I dont have the drivers on my laptop anymore for the dvd player, or the wireless internet... so i'm guessing it may have taken the 28pin or 12pin... w/e it is... driver out when the hardrive was replaced.
But does anyone know how to set the ports for Miscelaneous hardware in CromePro? Do you have to? I didnt w/ the chip burner, but idk~?
I've tuned w/ Uber... But it's the whole setting up the ---- that i dont get and getting hardware working in sinc. I'm the kind of guy that saves things off the internet and can never find them again~ That kinda ----.
I still cant figure out why my datalogging cable wont work... It might be my harddrive~ It's been replaced since i had Uber... I dont have the drivers on my laptop anymore for the dvd player, or the wireless internet... so i'm guessing it may have taken the 28pin or 12pin... w/e it is... driver out when the hardrive was replaced.
But does anyone know how to set the ports for Miscelaneous hardware in CromePro? Do you have to? I didnt w/ the chip burner, but idk~?
Thread
Thread Starter
Forum
Replies
Last Post