CEL in boost but no codes...
#1
CEL in boost but no codes...
well, i finaly got this thing running on a decent street tune and i freakin love it! its fun as hell does 70 mph burnouts like it aint nothin. im running a ls motor with a .48/.60 DSMs and a converted p28 on crome. i was driving around yesterday and i layed into it one good time and the CEL comes on and it starts backfireing and spitting and sputtering and wouldnt run for ----. if i slowly push on the throttle it wont do it everytime only some of the time but if i just nail it in 2nd or 3rd it starts doing it. i go to check the codes and there arent any...? i dont THINK im over shooting my stock map sensor at a little less than 10 psi but its always a possibility. the CEL has been flashing randomly befor too but i never throught much of it. i also got my 2.5 bar maps from freescale thursday, does anyone know how to wire them yet?
#2
Re: CEL in boost but no codes...
code out your cel's error code.. and get back to us.
instructions on how to do this:
http://www.askmehelpdesk.com/cars-tr...das-18139.html
instructions on how to do this:
http://www.askmehelpdesk.com/cars-tr...das-18139.html
#4
Re: CEL in boost but no codes...
Originally Posted by StinkyFeet
code out your cel's error code.. and get back to us.
instructions on how to do this:
http://www.askmehelpdesk.com/cars-tr...das-18139.html
instructions on how to do this:
http://www.askmehelpdesk.com/cars-tr...das-18139.html
thats the problem, there isnt one. i know how to get codes...jump the connector and the light stays on like when there are no codes....but it goes to hell and cel comes on when u get on it. i dont understand why it worked fine for 3 days then it went to ----...
#6
Re: CEL in boost but no codes...
looking at the top of the sensor from left to right what pins did you hook the wires to? should have a 5v ref., a return, and a common or something. im going to check my programming today and see if itll tell me anything
#7
Re: CEL in boost but no codes...
Pin 1 is the pin with a notch on one of its leg:
Pin 1 = Reference wire should be white on the car side (for some reason mine was pink/wht)
Pin 2 = Ground usually Green/Blue
Pin 3 = 5v should be Yellow/Green
Thats for OBD 1 DX wiring...I know VX and CX map sensor wire are like OBD 0 colors one of the color is red/something and its the 5v wire. Hope this helps.
Pin 1 = Reference wire should be white on the car side (for some reason mine was pink/wht)
Pin 2 = Ground usually Green/Blue
Pin 3 = 5v should be Yellow/Green
Thats for OBD 1 DX wiring...I know VX and CX map sensor wire are like OBD 0 colors one of the color is red/something and its the 5v wire. Hope this helps.
#8
Re: CEL in boost but no codes...
thats on the 6 pin free scale sensor that everyone was getting for free?
i fixed the problem with the cutting out i think. i hasnt done it since i went back and reburned my chip. i took some fuel out to bring my af ratio back up around 14. i reckon it was a bad burn.
i fixed the problem with the cutting out i think. i hasnt done it since i went back and reburned my chip. i took some fuel out to bring my af ratio back up around 14. i reckon it was a bad burn.
#10
Re: CEL in boost but no codes...
Originally Posted by zebvaj
yups...the others pin 4-6 are internals used by the motorola 2.5 bar map sensors. Go by what it posted at xenocron's webpage.
has anyone ever heard of a code 68? thats what i was getting befor i reburned my chip. then i hit a big bump in the road and broke 2 turbo mount bolts...damn hondas...