NEW CRX lsd clutch/flywheel, y8 head, other crap
Thread Starter
3.0 BAR
Joined: May 2006
Posts: 5,314
NEW CRX lsd clutch/flywheel, y8 head, other crap
I've decided to scrap my d-series build and go ls-vtec in the rex. I'll never finish a project 
- D16Z6 bare block, comes with girdle, oil pump, oil pan, but no crank/rods/pistons. Very clean with only minor surface corrosion in cylinders from sitting in the closet. Looks great. Could still see hatchmarks when I got it, but now has corrosion covering it, corrosion wipes off and is nothing to worry about.
$90
- D16Y8 full head, comes with dizzy, intake mani, and everything attached to it, was recently swapped onto my previous crx before it was totalled, so I know it works fine
$150
- LSD Motorsports d-series 6-puck sprung clutch with 285tq holding power, brand new, never used, with alignment tool and throwout bearing for 90-91 civic/crx
$200 ($36 off)
- LSD Motorsports 11-lb steel flywheel, brand new, never used
$130 ($30 off)
- 450cc dsm blues, bought from respectable member, said they were flow tested and cleaned, haven't used since then
$60
- D series acl bearings, brand new, complete set
$80 (cheapest I found was $97 on egay)
- D series z6/y8 metal headgasket, brand new
$35 ($45 on egay)
- D series valve cover seal and spark plug seals
$10
- 48/60 garret t3, was used by julio, bought by sinister, sold to me. Seems to be good condition but i'll be glad to check whatever you ask, I'm just not sure what to check
$120
- Downpipe for said turbo, has a bunghole and wastegate
$40
- Piping for said turbo
$20
- chinaman knockoff BOV, nipple for vac line broke but im sure you can rig it somehow
$10
- hf mani with 4 bolt flange(currently attached to turbo)
$25
- itr m4dTyT3 jdm spoiler, oem, dirty white
$100
- resistor box from crx
$15
- brand new Y8 ARP head studs
$90 ($15 cheaper)
- brand new d16 ARP rod bolts
$25 ($10 cheaper)
- brand new chinaman fmic
$90
- slim fan
$25
- lancer evo fuel pump, never used it, supposed to drop right in with minor common sense mods, since it's used on 300+ hp evos, should be fine for low boost honduhs
$25
- horny young virgin p28, some ---- overtightened the screws holding the cover on, and one or two are nearly stripped. Could be chipped, I don't know, can't get the ****** open.
$90
- 2nd gen CRX shell. I haven't seen it yet (i'm buying it for the b swap after I sell this ----), but the owner told me interior is rough, exterior is good shape, doesn't have the title (i'm not gonna mess with it) and doesn't know the status of it, won't have an engine in it, however I can donate an old but running a6 swap. No rust. I don't know any more details, just want to get some offers, don't be afraid to lowball. Should have more details in a day or two.
All prices are WITH shipping. I'm located in Madison, AL (zip 35758 if you want to get shipping estimates) and pickups are welcome. Buy more than one thing and I'll cut a few bucks off. Feel free to throw up offers and show your true lowballin spirit, just don't get ridiculous.
- D16Z6 bare block, comes with girdle, oil pump, oil pan, but no crank/rods/pistons. Very clean with only minor surface corrosion in cylinders from sitting in the closet. Looks great. Could still see hatchmarks when I got it, but now has corrosion covering it, corrosion wipes off and is nothing to worry about.
$90
- D16Y8 full head, comes with dizzy, intake mani, and everything attached to it, was recently swapped onto my previous crx before it was totalled, so I know it works fine
$150
- LSD Motorsports d-series 6-puck sprung clutch with 285tq holding power, brand new, never used, with alignment tool and throwout bearing for 90-91 civic/crx
$200 ($36 off)
- LSD Motorsports 11-lb steel flywheel, brand new, never used
$130 ($30 off)
- 450cc dsm blues, bought from respectable member, said they were flow tested and cleaned, haven't used since then
$60
- D series acl bearings, brand new, complete set
$80 (cheapest I found was $97 on egay)
- D series z6/y8 metal headgasket, brand new
$35 ($45 on egay)
- D series valve cover seal and spark plug seals
$10
- 48/60 garret t3, was used by julio, bought by sinister, sold to me. Seems to be good condition but i'll be glad to check whatever you ask, I'm just not sure what to check
$120
- Downpipe for said turbo, has a bunghole and wastegate
$40
- Piping for said turbo
$20
- chinaman knockoff BOV, nipple for vac line broke but im sure you can rig it somehow
$10
- hf mani with 4 bolt flange(currently attached to turbo)
$25
- itr m4dTyT3 jdm spoiler, oem, dirty white
$100
- resistor box from crx
$15
- brand new Y8 ARP head studs
$90 ($15 cheaper)
- brand new d16 ARP rod bolts
$25 ($10 cheaper)
- brand new chinaman fmic
$90
- slim fan
$25
- lancer evo fuel pump, never used it, supposed to drop right in with minor common sense mods, since it's used on 300+ hp evos, should be fine for low boost honduhs
$25
- horny young virgin p28, some ---- overtightened the screws holding the cover on, and one or two are nearly stripped. Could be chipped, I don't know, can't get the ****** open.
$90
- 2nd gen CRX shell. I haven't seen it yet (i'm buying it for the b swap after I sell this ----), but the owner told me interior is rough, exterior is good shape, doesn't have the title (i'm not gonna mess with it) and doesn't know the status of it, won't have an engine in it, however I can donate an old but running a6 swap. No rust. I don't know any more details, just want to get some offers, don't be afraid to lowball. Should have more details in a day or two.
All prices are WITH shipping. I'm located in Madison, AL (zip 35758 if you want to get shipping estimates) and pickups are welcome. Buy more than one thing and I'll cut a few bucks off. Feel free to throw up offers and show your true lowballin spirit, just don't get ridiculous.
1.5 BAR
Joined: Oct 2006
Posts: 964
Re: D-Series parts, almost complete turbo setup, crx shell, FS/FT
Originally Posted by Jorsher
- LSD Motorsports d-series 6-puck sprung clutch with 185tq holding power, brand new, never used
- LSD Motorsports 11-lb steel flywheel, brand new, never used
All prices are without shipping. I'm located in Madison, AL and pickups are welcome.
- LSD Motorsports 11-lb steel flywheel, brand new, never used
All prices are without shipping. I'm located in Madison, AL and pickups are welcome.
might want to post prices.
does the clutch come with PP and throw out bearing? how much for all that and the flywheel?
0.0 BAR
Joined: Jul 2005
Posts: 0
Re: D-Series parts, almost complete turbo setup, crx shell, FS/FT
damn. i knew you were in the huntsville area. but if i would have known madison....i spent a week visiting my uncle in madison over christmas. i should have looked you up
on a side note.....you wouldnt happen to have an extra bracket for the rear mount of a 5 spd b18a would you
on a side note.....you wouldnt happen to have an extra bracket for the rear mount of a 5 spd b18a would you
Thread Starter
3.0 BAR
Joined: May 2006
Posts: 5,314
Re: D-Series parts, almost complete turbo setup, crx shell, FS/FT
To the couple of you that pmed, and those waiting on prices, i'll have them in a few hours. Gotta get some crap done, gather all the parts, and head to someones house since I can't find the cable for my camera and only have the internets on my phone.
Sorry, don't have the b18 bracket.
Slim fan, I'll measure in a little bit, but I have another one and it fits perfectly on a half rad if that gives you an idea. I'll sell for 25 plus shipping?
Sorry, don't have the b18 bracket.
Slim fan, I'll measure in a little bit, but I have another one and it fits perfectly on a half rad if that gives you an idea. I'll sell for 25 plus shipping?
Thread Starter
3.0 BAR
Joined: May 2006
Posts: 5,314
Re: D-Series parts, almost complete turbo setup, crx shell, FS/FT
prices prices yes i know, told you they were coming and now they're up. I just needed to have some interwebs so I could get an idea on what this crap goes for.
Pics will be up in a few minutes if I can find something to read this memory card...damnit...answering pms now
Pics will be up in a few minutes if I can find something to read this memory card...damnit...answering pms now
