LS/Vtec Longblock PR4/Pr3 (NW)
I just had a bunch of parts laying in my garage so I slapped this together, I did put it in my car for a very short time just to make sure it ran and ended up taking it out for a different project. Anyways it runs fine, however it does need a water pump.
Engine 1992 B18a Integra LS (stock Pistons) Brand New Rings Head 91 B16a PR3 (just got resurfaced) PR3 Vtec Oil Pump TunerToys Block Fitting/High Pressure Line (for vtec) New Head Gasket SSautochrome Cams + Heavy Duty Valve Springs (stage 2) http://www.stockreco.com/aaaa20561.jpg Those cams are pretty much the same profile as skunk2's st2. They are already installed/adjusted and I'm not taking them out. https://www.homemadeturbo.com/misc/lsvtec1.jpg https://www.homemadeturbo.com/misc/lsvtec2.jpg https://www.homemadeturbo.com/misc/lsvtec3.jpg https://www.homemadeturbo.com/misc/lsvtec4.jpg No the tranny and intermediate shaft are not included and not for sale, sorry. Other than that everything else is included. PM me, or email me if your interested. If you have a bucket race seat (1 only) that you want to use as a partial trade/cash I'd be down for that too. $600.00 located in Everett, and I will Deliver it too if your within 15 miles from 98201. If you need vouches I'm sure I can supply a few =) Thanks, Jeff https://www.homemadeturbo.com/misc/horhay.JPG Oh, and Horhay approves the bottom end ;) |
Re: LS/Vtec Longblock PR4/Pr3 (NW)
good deal
|
Re: LS/Vtec Longblock PR4/Pr3 (NW)
thats a smokin deal!! wish i had the cash...
|
Re: LS/Vtec Longblock PR4/Pr3 (NW)
Good deal, but I have a question. What does the 91 B16A PR3 head come off of? Like which vehicle? I thought all the B16A's were from later model Civic Si's. :-\
JP |
Re: LS/Vtec Longblock PR4/Pr3 (NW)
Being a PR3, it came from the 1989-1991 JDM B16A which came in the EF8's and EF9's (CRX SiR's)
|
Re: LS/Vtec Longblock PR4/Pr3 (NW)
Originally Posted by SinisterCRX
Being a PR3, it came from the 1989-1991 JDM B16A which came in the EF8's and EF9's (CRX SiR's)
See that's what I was thinking that the only ones I knew of were teh SiR's that came abroad. They were the early model B16A's. Ewww, Jeff's all JDM and what not. :o LOL. Thanks Dan. JP |
Re: LS/Vtec Longblock PR4/Pr3 (NW)
Originally Posted by SinisterCRX
Being a PR3, it came from the 1989-1991 JDM B16A which came in the EF8's and EF9's (CRX SiR's)
I believe the itr head is also casted pr3 |
Re: LS/Vtec Longblock PR4/Pr3 (NW)
I should've said, for a PR3 being a 1991. Thanks for the correction though Chris.
|
Re: LS/Vtec Longblock PR4/Pr3 (NW)
so it is the mad tyte jdm head with the usdm valve cover.
looks liek a hell of a deal but do you have any vouches? :4 |
Re: LS/Vtec Longblock PR4/Pr3 (NW)
horhays name tag says octavio? i smell scammer!
|
Re: LS/Vtec Longblock PR4/Pr3 (NW)
why ssautochrome cams and valvetrain???
|
Re: LS/Vtec Longblock PR4/Pr3 (NW)
Originally Posted by spooncivic1
why ssautochrome cams and valvetrain???
bump for jeff... |
Re: LS/Vtec Longblock PR4/Pr3 (NW)
Originally Posted by spooncivic1
why ssautochrome cams and valvetrain???
Originally Posted by AbaZ
I just had a bunch of parts laying in my garage so I slapped this together
|
Re: LS/Vtec Longblock PR4/Pr3 (NW)
What kinda water pump is on the motor right now? GSR or LS?
|
Re: LS/Vtec Longblock PR4/Pr3 (NW)
LS
and its pending sell |
Re: LS/Vtec Longblock PR4/Pr3 (NW)
Do you still have that white caged CRX? How much for that car with this motor in it? :)
|
Re: LS/Vtec Longblock PR4/Pr3 (NW)
still have it pm me your number if so
|
Re: LS/Vtec Longblock PR4/Pr3 (NW)
Originally Posted by AbaZ
LS
and its pending sell |
Re: LS/Vtec Longblock PR4/Pr3 (NW)
Shoot deals like this, I want him to post up the blue bomber forsale. i may have to beg the wife to buy another car.
|
Re: LS/Vtec Longblock PR4/Pr3 (NW)
the azn backed out he wanted "papers" with it, lol...
Still for sale, PM's sent |
Re: LS/Vtec Longblock PR4/Pr3 (NW)
Originally Posted by AbaZ
the azn backed out he wanted "papers" with it, lol...
|
Re: LS/Vtec Longblock PR4/Pr3 (NW)
Originally Posted by AbaZ
the azn backed out he wanted "papers" with it, lol...
Still for sale, PM's sent |
Re: LS/Vtec Longblock PR4/Pr3 (NW)
Originally Posted by SinisterCRX
Being a PR3, it came from the 1989-1991 JDM B16A which came in the EF8's and EF9's (CRX SiR's)
|
Re: LS/Vtec Longblock PR4/Pr3 (NW)
Originally Posted by slo_crx1
Could've also come off an Integra X-si...they had pr3's too.
damn clean looking motor jeff, nice deal. |
Re: LS/Vtec Longblock PR4/Pr3 (NW)
Originally Posted by slo_crx1
Could've also come off an Integra X-si...they had pr3's too.
|
Re: LS/Vtec Longblock PR4/Pr3 (NW)
600 for all that and he wantedpapers? WTF?????
silly asian papers are for wetbacks :P |
Re: LS/Vtec Longblock PR4/Pr3 (NW)
any trades/part cash.
|
Re: LS/Vtec Longblock PR4/Pr3 (NW)
Pending sell again, hopefully picking up at 8pm to local hmt member.
|
Re: LS/Vtec Longblock PR4/Pr3 (NW)
will you ship it
|
Re: LS/Vtec Longblock PR4/Pr3 (NW)
I have a hard enough time shipping out small things, so that would be no.. definatly not shipping this thing.
|
Re: LS/Vtec Longblock PR4/Pr3 (NW)
too bad u couldnt wait 2 weeks. i could pay u in full
|
Re: LS/Vtec Longblock PR4/Pr3 (NW)
Originally Posted by AbaZ
I have a hard enough time shipping out small things, so that would be no.. definatly not shipping this thing.
|
Re: LS/Vtec Longblock PR4/Pr3 (NW)
Sold to me! ;D
Thanks alot for hookin up the good deal! |
Re: LS/Vtec Longblock PR4/Pr3 (NW)
Originally Posted by boosted-integra
Sold to me! ;D
Thanks alot for hookin up the good deal! That was a shitty transaction, I have never dropped a motor in the many years I've been working with cars. Next time I'm just gonna ship the ------- thing. But yes its Sold. |
Re: LS/Vtec Longblock PR4/Pr3 (NW)
sounds like a sweet transaction :y
I woulda told his ass to go the ---- home and not sell him the engine for (1) dropping it on me (2) for waiting my time. |
Re: LS/Vtec Longblock PR4/Pr3 (NW)
Originally Posted by AbaZ
Yea what a sweet way to end my 7 days off. Your buddies was 1 1/2 hours late, lost my phone number after I repeated it to him twice. Then gets lost after I gave him very easy directions. I told them I did not want to lift the motor out of the truck because my back was hurting. So they try lifting it out of the truck, the bigger of the 2 guys says man this is heavy I dont know. So I step in and lift it up, while we are lifting it the guy helping trips over his flip flops and drops the engine on my leg and I fall to the ground. My leg is all cut open in 4 spots and my finger is jacked.. Real sweet, the guy who helped lift was like are you ok? and the other guy was like... You think the motor is ok? uhhh yea. So the guy that didnt want to lift the engine must of saw that I was carrying my gun when I fell and started asking me stupid questions about it. I mean jesus ------- christ, I'm meeting 2 complete strangers at night time from bellingham (probably blakes friends). I've been jumped before I wouldnt be suprised if it happens again.
That was a shitty transaction, I have never dropped a motor in the many years I've been working with cars. Next time I'm just gonna ship the ------- thing. But yes its Sold. |
All times are GMT -5. The time now is 06:46 AM. |
© 2024 MH Sub I, LLC dba Internet Brands