FS: 60 trim .63 a/r T3
#1
![Default](https://www.homemadeturbo.com/images/icons/icon1.gif)
SOLD!
Well this has been my turbo for the past couple of years, I "de-turboed" my car a few months ago, so I need to sell my stuff..
Specs:
-T3, from the single turbo 300z
-.63 A/R turbine housing
-.52 A/R compressor housing
-60 trim compressor wheel
It was rebuilt about 7,500 miles ago, ceramic coated turbine housing and center section, balanced etc.. It has a stagger gap turbine ring, so it DOES NOT burn oil
No axial shaft play at all, well within spec radial shaft play.
This is the turbo I used to put down 200 whp at 4.5 psi on my h23, should be good to 250+ whp easy..
$190 shipped, I feel this is a good price considering I payed that much for the rebuild and stagger gap ring, much less the turbo itself.
Someone buy this so I don't have to put it up on ebay, please!
![](http://images.filecloud.com/307612/DSC00001.JPG)
![](http://images.filecloud.com/307614/DSC00002.JPG)
Well this has been my turbo for the past couple of years, I "de-turboed" my car a few months ago, so I need to sell my stuff..
Specs:
-T3, from the single turbo 300z
-.63 A/R turbine housing
-.52 A/R compressor housing
-60 trim compressor wheel
It was rebuilt about 7,500 miles ago, ceramic coated turbine housing and center section, balanced etc.. It has a stagger gap turbine ring, so it DOES NOT burn oil
![Cheesy](https://www.homemadeturbo.com/images/smilies/cheesy.gif)
This is the turbo I used to put down 200 whp at 4.5 psi on my h23, should be good to 250+ whp easy..
$190 shipped, I feel this is a good price considering I payed that much for the rebuild and stagger gap ring, much less the turbo itself.
Someone buy this so I don't have to put it up on ebay, please!
#3
![Default](https://www.homemadeturbo.com/images/icons/icon1.gif)
Originally Posted by 92_prelude_si
I knew I should have waited a little longer before ordering my oil lines and manifold. Do you still have the mani that goes with this and also the oil lines?
![Cheesy](https://www.homemadeturbo.com/images/smilies/cheesy.gif)
Aftermarket stainless DSM manifold, redrilled
stainless oil lines/firewall T/restrictor inlet etc etc..
#5
![Default](https://www.homemadeturbo.com/images/icons/icon1.gif)
Originally Posted by 92_prelude_si
How much for all of it? I was ready to slap everything on but now I see this and want to sell my other stuff!
I have a 44mm wastegate, the manifold, a dumptube, all stainless downpipe, the turbo..etc etc..
I have a DSM BOV and DSM injectors too..
Like any other setup I have seen for the H23 you will have to lose the front motor mount and shave 1/4" off the front of the block (pretty easy with a grinder, i did it in like 5 minutes)..
the wastegate might hit the hood when the motor moves around, so it MIGHT be best to cut and reweld the wastegate elbow on the manifold a bit lower. I don't know if you have the tools to do this, if you decide to buy it all I can do it for you.
I would sell it all for like $650 shipped
cardomain.com/id/garnxe for pics and stuff
#8
![Default](https://www.homemadeturbo.com/images/icons/icon1.gif)
Originally Posted by sliva001
pmed. will a regular 5 bolt fit on the exhaust side? where are you located?
#9
![Default](https://www.homemadeturbo.com/images/icons/icon1.gif)
Originally Posted by 92_prelude_si
I have a 44mm wastegate w/d.tube, dsm injectors, dsm bov and everything else. I guess all I need to change is the turbo, mani, and oil lines. Right?
Well then yea the turbo, manifold, and oil lines would be fine. I would also use my downpipe because it is already guaranteed to fit my turbo/manifold location. It will bolt right up and it's all 304 stainless, with a flex section there, and it has the flange there too..