2.5in. Charge Pipe Angles (steel)
01-08-2003, 12:51 AM
#1
0.0 BAR
Thread Starter
Join Date: Dec 2002
Posts: 0
2.5in. Charge Pipe Angles (steel)
ok.. well im getting my charge pipes made this weekend. Out of a 10ft 2in. steel pipe i got at Home Depot... im going to have some material left over and i was thinking of making some 90* and U angles ... I want to know how many people would be intersted in getting some? Im not to sure how much they will cost yet... but come on, im getting them bent in Mexico so you know its gonna be dirt cheap. I just wanted to know how many people would be interested and what angles they would want. let me know... ok...
01-08-2003, 10:56 AM
#2
0.0 BAR
Join Date: Jan 2003
Posts: 25
Re:2in. Charge Pipe Angles (steel)
I could use like a 115 degree bend. Dont car how much pipe you use, the shorter the better 
Let me know
Nconte@novell.com
Thanks,
Nick
Let me know
Nconte@novell.com
Thanks,
Nick
01-08-2003, 09:47 PM
#3
0.0 BAR
Thread Starter
Join Date: Dec 2002
Posts: 0
Re:2.5in. Charge Pipe Angles (steel)
----... my bad actually its 2.5in diameter(not 2in).... anyways heres a pic of a pipe they made for my bros exhaust... painted it red cause it was dirty... and looked like ----... but anyways notice its not pinched or anything... its 2.5in diameter from start to finish
01-09-2003, 01:25 AM
#4
0.0 BAR
Join Date: Jan 2003
Posts: 20
Re:2.5in. Charge Pipe Angles (steel)
How much would you charge if I gave the pipe deminsions i need for my turbo kit and you get it bent and ship it to me. I need the complete upper and lower inercooler piping. Let me know if you will do this. If not I can probably just tell you the bends i need and work from there.
Thanks
Cody
Thanks
Cody
01-09-2003, 11:20 AM
#5
0.0 BAR
Thread Starter
Join Date: Dec 2002
Posts: 0
Re:2.5in. Charge Pipe Angles (steel)
i dont know... it would be kinda hard to bend something without knowing if its gonna fit... thats why i have to take my car up there... and bolt on the turbo to the car this way they can bend it and test fit it as they go along... but maybe it can be done... il let you know by monday... just so i know... what setup are you going to be running, car model... turbo? intercooler type? turbo intake pointing towards driver side, passenger side... ---- like that... let me know if you have a picture... that would help a lot...
01-10-2003, 02:10 PM
#7
0.0 BAR
Thread Starter
Join Date: Dec 2002
Posts: 0
Re:2.5in. Charge Pipe Angles (steel)
draw a pic and post it... with measurements and angle degrees... and ill tell you if its possible... or maybe i should draw on of the top view... and then one of a side view of an engine and turbo... and you just add the piping where you want it to go... that would make ---- a whole lot easier... but when i get my ---- done... ill post pics and you tell me if thats something similar to what you want or not...
01-11-2003, 04:48 PM
#8
0.0 BAR
Join Date: Jan 2003
Posts: 20
Re:2.5in. Charge Pipe Angles (steel)
I have a 1994 Civic coupe with the AC and power steering units taken out. My car has a LS engine with GSR intake manifold. I have a T3 Turbo with a Starion intercooler. The piping needs to start on the drivers side I will be able to give you deminsions whenever I have time to do a test mount and get some measurements in.
01-11-2003, 06:10 PM
#9
1.0 BAR
Join Date: Dec 2002
Posts: 564
Re:2.5in. Charge Pipe Angles (steel)
hey orangecivic, I love your signature at the bottom of every post "Dont you love ricers today? I beat a Volvo Type R" that's ------- hilarious. 
By any chance you want to sell your starion intercooler?
By any chance you want to sell your starion intercooler?
