z6 swap in 91 crx dont run SHES ALIVE!!!!!!!!!!!!!!!!!!!!!!!!!!!!
09-28-2004, 07:05 PM
#21
0.0 BAR
Join Date: Apr 2004
Posts: 0
Re:z6 swap in 91 crx dont run NEED HELP!!!!!!!!!!!!!!!
Originally Posted by ShoPow
Sorry been at work all day. I just bought new plugs and wires . My firing order is set the way it is on the pic you loaded. Gonna go mess with it now for a while and let you guys know whats up. I appreciate all the help. Thanks.
Chris
Chris
09-28-2004, 07:47 PM
#22
0.0 BAR
Join Date: Sep 2004
Posts: 27
Re:z6 swap in 91 crx dont run NEED HELP!!!!!!!!!!!!!!!
if u are not getting spark at the end of your plugs. Back up and go to your coil. find the signal wire from the ecu that ungrounds the coil to spark the plug. hook up a test light to B+ and when u crank it should flash if this hppens problem is eather coil wires or cap rotor. if you dont get a signal it is eather a sensor or bad ecu or broken wire somwhere back there
09-28-2004, 10:10 PM
#23
1.0 BAR
Thread Starter
Join Date: May 2003
Posts: 209
Re:z6 swap in 91 crx dont run NEED HELP!!!!!!!!!!!!!!!
Put in new plugs and wires. Still no start.
Sprayed starter fluid in the ic piping. No start.
Couldnt check for spark cause I was all by my self and no matter how much my mom complains about my car she wont help out for 5 mins. But what could be causing it if both my dizzys dont work. Ive been running the chipped ecu for the past 6 months so I dont think that theres anything wrong with that. I used the crx engine harness so I didnt not have to change any wiring.
Sprayed starter fluid in the ic piping. No start.
Couldnt check for spark cause I was all by my self and no matter how much my mom complains about my car she wont help out for 5 mins. But what could be causing it if both my dizzys dont work. Ive been running the chipped ecu for the past 6 months so I dont think that theres anything wrong with that. I used the crx engine harness so I didnt not have to change any wiring.
09-28-2004, 11:38 PM
#25
0.0 BAR
Join Date: Feb 2003
Posts: 0
Re:z6 swap in 91 crx dont run NEED HELP!!!!!!!!!!!!!!!
I'd check the timing. I know when I did my headgasket the timing wasn't all that far off, and the car wouldn't start
Timing
Fuel
Spark
Compression
That's all the elements you'll need to fire. One of them isn't there.
Timing
Fuel
Spark
Compression
That's all the elements you'll need to fire. One of them isn't there.
09-28-2004, 11:59 PM
#26
1.0 BAR
Thread Starter
Join Date: May 2003
Posts: 209
Re:z6 swap in 91 crx dont run NEED HELP!!!!!!!!!!!!!!!
The igntion timing by the dizzy or the by the timing belt?
When I the cam is straight up and I look through the notch on the timing belt cover It lines up perfectly with the one notch thats all by itself. Thats TDC right?
Ive tried adjusting the dizzy back and forth but it still didnt start.
When I the cam is straight up and I look through the notch on the timing belt cover It lines up perfectly with the one notch thats all by itself. Thats TDC right?
Ive tried adjusting the dizzy back and forth but it still didnt start.
09-29-2004, 08:19 AM
#27
0.0 BAR
Join Date: Apr 2004
Posts: 0
Re:z6 swap in 91 crx dont run NEED HELP!!!!!!!!!!!!!!!
Originally Posted by ShoPow
Ive tried adjusting the dizzy back and forth but it still didnt start.
i sitll think you have your spark plug wire in the wrong spot. you would still have spark, and you could move the dizzy and your timing could be dead on but if your firing order is off..you would be fucked.
take pictures and post...
09-29-2004, 11:53 AM
#30
3.0 BAR
Join Date: Feb 2003
Posts: 9,089
Re:z6 swap in 91 crx dont run NEED HELP!!!!!!!!!!!!!!!
ok..maybe when you pulled the dist you're not linging it all back up properly.
set the motor to #1 TDC compression stroke. then put the dist on and make sure it's aligned to the #1 terminal. bolt everything back down and try starting it.
set the motor to #1 TDC compression stroke. then put the dist on and make sure it's aligned to the #1 terminal. bolt everything back down and try starting it.
