HomemadeTurbo - DIY Turbo Forum

HomemadeTurbo - DIY Turbo Forum (https://www.homemadeturbo.com/)
-   Hybrid/Tech (https://www.homemadeturbo.com/hybrid-tech-8/)
-   -   swapped harness now shit not workin right (https://www.homemadeturbo.com/hybrid-tech-8/swapped-harness-now-shit-not-workin-right-91178/)

dcivic 04-17-2008 01:33 PM

swapped harness now shit not workin right
 
97 CX hatch w/ B18c1
-I believe Ecu is a Skunk chipped P 72
I swapped my engine harness w/ the one I got back from Rywire. Everything seems to be plugged back in. I put in a new O2 sensor and connected it as well.
I had to redo the injector clips , by using my old clips that plug to Black (thin top) of injectors.

The ---- starts, but when I give it gas it chokes and dies. Any suggestions, since the car ran before swapping harnesses? Help a noob out GURUs.

HMTguy 04-17-2008 01:45 PM

Re: swapped harness now shit not workin right
 
Might want to be 100% sure of what bin you are running in your ecu to eliminate further headaches.

Any CELs?

dcivic 04-17-2008 03:27 PM

Re: swapped harness now shit not workin right
 
I do have a CEL. I reset ECU multiple times, and as soon as i start car up it pops. I know this is a noob question, but would the car even start if injector wiring may have gotten connected wrong way? I am pretty sure that all the wiring for injectors are correct as I swapped them one at a time.

HMTguy 04-17-2008 04:02 PM

Re: swapped harness now shit not workin right
 
First things first, what is the CEL for?

whiterice 04-17-2008 06:20 PM

Re: swapped harness now shit not workin right
 
I think you have to find the answers to the above questions first. ^^

Also, skunk IM or gsr? which injectors?

dcivic 04-19-2008 04:59 PM

Re: swapped harness now shit not workin right
 
thanks for replies guys. I connected the wires to the service connector and checked the CEL. It came up with a 1 ( Mass or Volume Air Flow Circuit Malfunction). I ended up swapping some connectors around around, and it got rid of the CEL. Im a noob and this is my first engine harness swap :1

So now when I start the car it would run, but its running rough. When I give it gas it kills it. I was wondering if i need to get my ECU rechipped since it did not have all of the sensors connected before i put in the Rywire harness. The ECU is a Spoon Chipped p28 ( disregard my noobness on earlier post of p 72 w/ Skunk).

I know nothing about chipping ECUs, but this is the chip thats inside. Is this a reburnable chip?

http://a37.ac-images.myspacecdn.com/...c900a92104.jpg

http://a407.ac-images.myspacecdn.com...b8b944c746.jpg

http://a483.ac-images.myspacecdn.com...1c2fc7738a.jpg

EG-prince 04-19-2008 10:55 PM

Re: swapped harness now shit not workin right
 
ah the ole map/tps switch. gets em every time.

b18. 04-19-2008 10:58 PM

Re: swapped harness now shit not workin right
 
Spoon chip is bullshit.

What the hell is really in your ecu.

dcivic 04-19-2008 11:24 PM

Re: swapped harness now shit not workin right
 
Spoon chip is what buddy said is in it. Spoon maps / bin whatever.... ::)
Like I said before I dont know much about chippin, but the ---- pulled hard. And as far as what is exactly in there... i dunno. i posted pic of chip that was put in.

EG-prince 04-19-2008 11:39 PM

Re: swapped harness now shit not workin right
 
"spoon chips" are usually generic ebay crap basemaps. You should probably pay xeno or anyone else with a bit of tuning competence to send you a new chip with a proper basemap


All times are GMT -5. The time now is 06:10 AM.


© 2024 MH Sub I, LLC dba Internet Brands