HomemadeTurbo - DIY Turbo Forum

HomemadeTurbo - DIY Turbo Forum (https://www.homemadeturbo.com/)
-   Hybrid/Tech (https://www.homemadeturbo.com/hybrid-tech-8/)
-   -   Problems and i need answers... more questions sooooo close (https://www.homemadeturbo.com/hybrid-tech-8/problems-i-need-answers-more-questions-sooooo-close-49547/)

d16u7nh 11-06-2005 03:07 PM

Problems and i need answers... more questions sooooo close
 
ok so my pistons dont fit th z6 block. and i fucked up the rocker assembly for the a6. what i have know is a whole z6 engine, head and trans. which im just going to put in my 90 crx dx. what problems am i going to run in to? it a vtec head so i need to hack a vtec in right. what about the trans its a hydro do i need anything different. will the dx axles fit the z6 trans. and i still do the same wireing job as a mini me swap. i need a pm8 right not the pm6. im still gonna use the same a6 act clutch. what am i forgeting.

boosted_b16 11-06-2005 03:57 PM

Re: Problems and i need answers.
 
god damn your lost huh? ok for starter its a dx so you either have to use the dx tranny, which will bolt right up to the z6 block, or if you want to use a si/hf or the z6 tranny then you need hf/si axles and front hubs as the dx is the only one that uses the smaller hubs/axles, also if you use the hydro z6 tranny you will need a hydro to cable conversion kit, i would reccomend if you need it done cheap and fast to just throw in the dx tranny for now, then later upgrade the axles/hubs to hf/si, then just use a 88-91 hf/si tranny, as far as the wiring, yes you need to start by doing the dpfi to mpfi wiring mods, and as far as vtec goes, it all depends on how your going to run vtec, and if you use a chipped ecu or not, i would reccomend using a pm6 ecu and then chipping it with turbo edit and you can run simple one wire vtec form the chipped pm6, or if you have a v-afc laying around just run a stock pm6 ecu, then install the v-afc and use it to run vtec....good luck mang...

d16u7nh 11-06-2005 04:59 PM

Re: Problems and i need answers.
 
ok thats sorta what i thought. the dx tranny stays for now. the trubo edit what that gonna run me and how do i get one..? thanks alot.

HMT-Admin 11-07-2005 03:46 AM

Re: Problems and i need answers.
 
The Z6 trans is Hydro and will not work well in a EF chasis, I dont know of anyone who has done it, you would need a custom pass side mount and a 92+ eg rear mount. Plus some type of pedal assembly that was setup for hydro. Definatly not worth it, most people just swap in SI trannys.


Originally Posted by boosted_b16
if you want to use a si/hf then you need hf/si axles and front hubs as the dx is the only one that uses the smaller hubs/axles,

No, I think you got mixed up. DX/SI's use the larger hubs and HF's use the smaller ones.


also if you use the hydro z6 tranny you will need a hydro to cable conversion kit,
Nobody makes a Hydro kit for D-series in a EF. It is possible you could modify the B-series hasport kit, but you still would need a custom mount mount.

To run a Z6 in a DX you will first need to do the DPFI-MPFI wiring. Once that is done I'd go with a chipped PS9 I think it is? They have the output for vtec.

Jeff

d16u7nh 11-07-2005 01:34 PM

Re: Problems and i need answers.
 
so i use the dx tranny and the mini me wireing

HMT-Admin 11-07-2005 05:02 PM

Re: Problems and i need answers.
 
yup

d16u7nh 11-10-2005 03:13 PM

Re: Problems and i need answers.
 
the rocker assembly off my d15 head in the 90 rex will fit my a6 head. ?

sohcpwr 11-11-2005 03:09 PM

Re: Problems and i need answers... more questions sooooo close
 
i think you will only get 1 bolt to hold the obd0 dizzy in the head


All times are GMT -5. The time now is 10:38 PM.


© 2024 MH Sub I, LLC dba Internet Brands