HomemadeTurbo - DIY Turbo Forum

HomemadeTurbo - DIY Turbo Forum (https://www.homemadeturbo.com/)
-   Hybrid/Tech (https://www.homemadeturbo.com/hybrid-tech-8/)
-   -   LS rods in Dseries block (https://www.homemadeturbo.com/hybrid-tech-8/ls-rods-dseries-block-32408/)

HMT-Admin 01-02-2005 02:37 AM

Re:LS rods in Dseries block
 
fitting the ls rods in a d-series isnt a problem, you need to resize the journal end, and use aftermarket pistons. Stock pistons and the ls rods aint gonna happen.



adrenajunky 05-19-2005 06:23 AM

Re:LS rods in Dseries block
 

Originally Posted by AbaZ
fitting the ls rods in a d-series isnt a problem, you need to resize the journal end, and use aftermarket pistons. Stock pistons and the ls rods aint gonna happen.
[/quote
then what about vitara pistons and ls rods?]


ZC4ME 05-19-2005 10:09 AM

Re:LS rods in Dseries block
 

Originally Posted by adrenajunky

Originally Posted by AbaZ
fitting the ls rods in a d-series isnt a problem, you need to resize the journal end, and use aftermarket pistons. Stock pistons and the ls rods aint gonna happen.
[/quote
then what about vitara pistons and ls rods?]


You used one of your first three posts to bring this thread back from the dead, WTF?!?!?

BenDover 05-21-2005 10:27 PM

Re:LS rods in Dseries block
 

Originally Posted by ZC4ME

Originally Posted by adrenajunky

Originally Posted by AbaZ
fitting the ls rods in a d-series isnt a problem, you need to resize the journal end, and use aftermarket pistons. Stock pistons and the ls rods aint gonna happen.
[/quote
then what about vitara pistons and ls rods?]


You used one of your first three posts to bring this thread back from the dead, WTF?!?!?


juli0_bustamante 05-22-2005 03:25 AM

Re:LS rods in Dseries block
 

Originally Posted by hotrex
im tellin him not to be a half ass ------, why learn by blowin 1000 on a motor when for 1280 you got a nice bulletproof setup, ---- dog, i still love you

so all that punch me in the face ---- and the beaner comments were said while under the influence???? ahhh now i fell bad for calling you a piece of ----....well maybe not, but im still hurt :'(.

rudebwoy 05-22-2005 10:33 AM

Re: LS rods in Dseries block
 
if you are going to buy forged pistons go ahead and get forged rods, I think the rods are more important anyway. I learn bad by being cheap, now I am rebuilding again and I just finish the build. I did not bore over my clinders after I discovered scoring, now I am burning ouil bad, I had to order another set of oversize pistons to do it again, my head gasket cost me $150 and the rod bearings cost me 280 euros so dont be half ass. I know its a different situation but it will turn out the same results. do it right the first time you wont have to do it twice.

d16u7nh 05-22-2005 02:03 PM

Re: LS rods in Dseries block
 
dude... i had about $1000 in my si a6 engine and i went with shot peened rods and i busted the #3 rod and spun a bearing ------ up the whole engine. now after two blocks and about $2000 im in for the next engine and i will by aftermarket rods and arp bolts to hold them. so when im slammin thru gears and redlining i know my piston , rod combo is not failing. its well worth the extra $200-$300.

sparkwon 05-24-2005 03:30 PM

Re:LS rods in Dseries block
 

Originally Posted by hotrex
im tellin him not to be a half ass ------, why learn by blowin 1000 on a motor when for 1280 you got a nice bulletproof setup, ---- dog, i still love you

why the ---- does no one have a problem with people throwin around the n bomb like its all good? i will be the first "------" to tell you that i dont appreciate that ---- at all, especially coming from that peckerwood cracker. i can give a good guess as to why no one says anything, but that doesnt make it alright for the mods to not do their job and moderate threads.

Bone1 05-25-2005 05:32 AM

Re: LS rods in Dseries block
 
hey NEWBIE...............I totally agree with you!

"N" bombs not needed, grow up!


All times are GMT -5. The time now is 04:26 AM.


© 2024 MH Sub I, LLC dba Internet Brands